Finally got a MS3x
OK, so. I bought one with a harness, boost solenoid and a VTPS.
As far as installation, I know it's different than the MSPNP. The harness will just hook up to the MS3x and the stock harness, correct? Give me some ideas for where to mount this. Glove box a good location? Can someone load me a file they have that I can use to get the car started or can I download it somewhere? The boost solenoid, EBC Electronic Boost Control Solenoid Kit DIYAutoTune.com says to just put it between the boost source and the wastegate? Boost source needs to be closest to TB right? The wiring for the VTPS. Wiring Up Auto (Variable) Tps - Forced Induction & N/A Power Mods - MX5Nutz Forum Correct or not? I'm sure I will have more once I get it here in my hands. Thanks for any help. |
Ok so scratch the VTPS wiring, guy shipped me an already made one!
Also the wiring, I see how it works now that I have it here. Would a base file for the mspnp work on the ms3x? |
Ok so I'm reading all this crap about the ms3x
http://www.msextra.com/doc/pdf/MS3XV30_Hardware-1.3.pdf All of this is already wired correctly with a Braineack build ms3x right? I should be able to just install the box, hook it up, load a default tune, and start tuning? |
Halp.
I'm reading the ms3x has a basemap loaded on it. But I bought this 2nd hand. Does anyone have a map they could send me? 1.6l greddy kit no cat 550cc injectors or even a basemap (I can't seem to find it) for a 1.6l afm-less. Thanks for any help. |
3 Attachment(s)
With the 1.6 harness does the MS3x use the same ground (sensor gnd) as the stock ecu? I believe the answer is yes but I can't find a definite answer. Just want to make sure so I can keep my wideband ground with it.
Some pictures to hopefully get some help. https://www.miataturbo.net/attachmen...ine=1412185009 Attachment 235248 Attachment 235249 |
Can't get tunerstudio to connect.
Followed the msextra topic. Get to the part where you portcheck and it doesn't recognize the ms3x. Any help? I've tried different COM's, I'm using a USB cable. |
Originally Posted by whinin
(Post 1172200)
Can't get tunerstudio to connect.
Followed the msextra topic. Get to the part where you portcheck and it doesn't recognize the ms3x. Any help? I've tried different COM's, I'm using a USB cable. |
Yes. It shows COM1 USB under ports in Device Manager.
|
Tried on another laptop, still no go.
Anyway I can check to see if the MS3x is getting power? Should there be lights on somewhere? |
4 Attachment(s)
Tried a $25 serial to usb cable, still no luck.
I took the case off the ms3x and snapped some pictures. I'm not much of an electrical guy but I didn't see anything fried. I tried to get most of the capacitors/resistors in these shots. Attachment 235244 Attachment 235245 Attachment 235246 Attachment 235247 Any help is appreciated. I have tried looking for posts related to this problem but none of them have helped. |
2 Attachment(s)
I don't know if this helps either.
Attachment 235242 Attachment 235243 This is supposed to be for a 1.6L |
Can you post a screenshot of device manager? Are you sure you got the drivers?
|
1 Attachment(s)
|
Drivers are from FTDI most up to date from Virtual COM Port Drivers
|
Do you have a multimeter?
|
Have you tried a USB cable? Connected to the MS3?
|
Also what USB to serial converter are you using.
|
I have tried a USB cable and a serial to USB on two different laptops.
I do have a multimeter, though still newbish with it. |
The one from Radio Shack. Gigaware.
|
Think you could figure out how to do step 24 on this guide?http://www.msextra.com/doc/ms3/build_manual.html
|
All times are GMT -4. The time now is 06:15 AM. |
© 2024 MH Sub I, LLC dba Internet Brands