FYI new version of HR code available
#1
Supporting Vendor
Thread Starter
iTrader: (5)
Join Date: Jun 2006
Location: Duluth, GA 30097
Posts: 803
Total Cats: 0
FYI new version of HR code available
KeithG has continued to plug away at the issue some of you were having going from 029 standard MS1E code over to the HR code and getting the phantom 2500rpm rev limiter and he thinks he's nailed it. I ran into this as well and fixed it by manually copying all my .msq settings over, but he thinks he's nailed it down to a potential code issue when certain features were enabled, such as CLT/IAT related air density, which I know alot of you like to use.
Here's the latest--
http://ys3al35l.googlepages.com/hr_10g.zip
If you have any issues post here and we'll make sure Keith is aware of the thread and can chime in if needed.
Here's the latest--
http://ys3al35l.googlepages.com/hr_10g.zip
If you have any issues post here and we'll make sure Keith is aware of the thread and can chime in if needed.
__________________
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
#3
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,039
Total Cats: 6,604
Yup- even though I don't have IAT/CLT density in use, I went to it the other day while un-downgrading from 029y4 (having gone backwards trying to troubleshoot an unrelated problem.)
While I can't speak to the phantom rev limit problem, it may just be my imagination but the engine seems to start a little better- like it "catches" and fires up about one cycle earlier.
While I can't speak to the phantom rev limit problem, it may just be my imagination but the engine seems to start a little better- like it "catches" and fires up about one cycle earlier.
#4
Supporting Vendor
Thread Starter
iTrader: (5)
Join Date: Jun 2006
Location: Duluth, GA 30097
Posts: 803
Total Cats: 0
<- behind the times
Keith emailed me on it Saturday so I wanted to FYI you guys....
Keith emailed me on it Saturday so I wanted to FYI you guys....
__________________
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
#5
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Jerry, I installed this code on Saturday. No issues to report so far, other than the VE table is *completely* off. Also, my CLT seems a bit higher. Sounds odd, but it's registering at 207 during cruise, instead of 203. The positive side is idle is smoother and acceleration is snappier. I should have it dialed in good enough to take some pulls on Saturday.
See you Saturday
See you Saturday
#6
i guess ill bite and update. maybe that should fix my starting issues. im having problems where the engine would bog for several seconds right after the engine starts and fires up. i need to press the accelerator for several seconds before the engine starts to idle normally. does anyone know what could this be? when its hot, it bogs so much that it stalls the motor, and i need to restart the motor and give gas until the idle settles.
#7
Supporting Vendor
Thread Starter
iTrader: (5)
Join Date: Jun 2006
Location: Duluth, GA 30097
Posts: 803
Total Cats: 0
Actually, that sounds like an entirely different situation.... more than likely afterstart enrichments needing to be dialed in.
__________________
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
#9
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,039
Total Cats: 6,604
edit- Jerry beat me to it.
#11
Tim(saboteur) came round the other night and we put the hires onto my MSPNP. It's running alot smoother right through the rev range and seems to pull just a little better after some tuning too. Just as others have reported the ve table is way off(like 10:1 under load N/A) but that is sorting itself out.
I still cant get the idle control to work at all with the nb idle valve, pretty sure this is down to the cams, so steady dc in warmup only mode it is.
Tim
I still cant get the idle control to work at all with the nb idle valve, pretty sure this is down to the cams, so steady dc in warmup only mode it is.
Tim
Thread
Thread Starter
Forum
Replies
Last Post