Inverted/non-inverted spark?
#1
Senior Member
Thread Starter
iTrader: (14)
Join Date: Nov 2004
Location: Ambler, PA
Posts: 1,275
Total Cats: 1
Inverted/non-inverted spark?
I don't ever remember a conclusion to the discussion about settings. I know quite a few people are running inverted spark with kags mods without a problems and all the ms-pnp are using non-inverted setting. Just wondering if anyone ever figured it out? Granted I was running inverted spark without problems, but it is still a bit concerning.
#2
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
I am running inverted spark with kags/braineacks mods. I am almsot positive that spark ended up working both ways with those mods, but decided to leave it with inverted and I have had no problems so far.
#3
spark needs to be inverted with the old way mods... nearly 3000miles now doesn't lie. i don't know why the MS pnp is different, but apparently it needs to be. and also the whole thing about the different wheel decoder settings leads me to believe that the MS Pnp .msq is not directly compatible with a board modified in the old way and vice versa.
#6
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,494
Total Cats: 4,080
If it aint broke, don't break it....
Tom I trust running inverted will be fine....Once I get yours I can make sure you have the same spark mod as me...I'm sure you do...I've been running inverted as well, no problems here.
I believe if your use the wheel decoder settings like the new MSPnP and DIY instructions, then you need non-inverted. (rising vs. falling)
Tom I trust running inverted will be fine....Once I get yours I can make sure you have the same spark mod as me...I'm sure you do...I've been running inverted as well, no problems here.
I believe if your use the wheel decoder settings like the new MSPnP and DIY instructions, then you need non-inverted. (rising vs. falling)
#10
Well I guess I can answer the question about inverted vs non-inverted.
I played around with DIY's PnP map 2 weeks ago. Maybe let it run for 45 seconds. Loaded up my MSQ and have actually daily drove my car for the last 2 weeks.
Today, after wiring up the shift light, I start the car to test it and it sounds like its running on 3 cylinders. I had messed with a plug wire earlier doing something else, so I replaced it. Still runs like crap, and dies.
All it does is turn over, fuel all over the sparkplugs = Fuel no spark = blown igniter.
I should have just left well enough alone :(
I played around with DIY's PnP map 2 weeks ago. Maybe let it run for 45 seconds. Loaded up my MSQ and have actually daily drove my car for the last 2 weeks.
Today, after wiring up the shift light, I start the car to test it and it sounds like its running on 3 cylinders. I had messed with a plug wire earlier doing something else, so I replaced it. Still runs like crap, and dies.
All it does is turn over, fuel all over the sparkplugs = Fuel no spark = blown igniter.
I should have just left well enough alone :(
#11
Supporting Vendor
iTrader: (5)
Join Date: Jun 2006
Location: Duluth, GA 30097
Posts: 803
Total Cats: 0
Kags mods = inverted spark output
DIYAutotune's mods, or the MSPNP = non-inverted spark output
DIYAutotune's mods, or the MSPNP = non-inverted spark output
__________________
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
#12
I've done mine like this. Does that mean I need non-inverted?http://www.diyautotune.com/images/ca...t_mods_med.jpg
Thread
Thread Starter
Forum
Replies
Last Post