Anyone got a base fuel map for a 99-00?
#1
Anyone got a base fuel map for a 99-00?
I''ve recently got my MS up and running and now it's time for tuning.
As there are no PnP maps for the 99-00 cars (it's VE im after) I'm wondering if anyone would care to share their map?
I've been trying to tune my VE table from the 96 PnP VE Table for a few evenings now but the figures are quite a bit out. i.e. map is far too rich that the LC-1 reads lean and therefore MLV will generate incorrect data from this occurance.
Cheers,
Craig
As there are no PnP maps for the 99-00 cars (it's VE im after) I'm wondering if anyone would care to share their map?
I've been trying to tune my VE table from the 96 PnP VE Table for a few evenings now but the figures are quite a bit out. i.e. map is far too rich that the LC-1 reads lean and therefore MLV will generate incorrect data from this occurance.
Cheers,
Craig
#3
I can't confirm the req fuel as Im at work at the moment. Im on stock injectors with stock pressure so what values should I have in there?
My LC-1 is perfect. I did have trouble with it throwning heater calibration codes at me, but since soing a full re-cal it's been fine and showed good idle AFRs on the stock fuel table of ~ 14.7:1. I then switched control of the fuel to the MS and have since been finding it hard to tune the table past 4krpm at light loads when up to full operating temp.
It's also worth noting that my MS has no TPS input form my car, Im running it off the MS MAP sensor. I followed your install schematic for my car and all worked perfectly - thanks for that Zaphoid!
Any base tables or req fuel info to compare to mine would be appriciated.
My LC-1 is perfect. I did have trouble with it throwning heater calibration codes at me, but since soing a full re-cal it's been fine and showed good idle AFRs on the stock fuel table of ~ 14.7:1. I then switched control of the fuel to the MS and have since been finding it hard to tune the table past 4krpm at light loads when up to full operating temp.
It's also worth noting that my MS has no TPS input form my car, Im running it off the MS MAP sensor. I followed your install schematic for my car and all worked perfectly - thanks for that Zaphoid!
Any base tables or req fuel info to compare to mine would be appriciated.
#5
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,025
Total Cats: 304
Here is a .msq that I used to run on my '99 when I ran MS-1 in parallel with the stock injectors. I think I used to run about 7psi on this one. I didn't open it, I just read the title...(I had it stored in my .msq archive). Try it out for your comparing or whatever you need it for.
99stockinj.msq
99stockinj.msq
#8
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
I was commenting on the general nature of requesting a fuel table.
If this car has the standard 1.6 electronics and the binary tps, then its fine unhooked with some work. I don't run the TPS at all and it drives wonderfully. Actually, I get a lot of **** for it, but it drives wonderfully.
If this car has the standard 1.6 electronics and the binary tps, then its fine unhooked with some work. I don't run the TPS at all and it drives wonderfully. Actually, I get a lot of **** for it, but it drives wonderfully.
#10
How old exactly are you? Feel smart because you have more posts? Go read up on your own questions when you started with MS in 2007.
Nothing wrong about asking a VE table. I'd call him smart to ask for one instead of just throwing in some random numbers and hoping it'll be ok.
Did your VE table became populated out of thin air? Or did someone else do it for you while you were crying for help?
He would be even smarter if he asked for a AFR table, but even then, he'd need the VE as well.
Try this with stock injectors, req fuel 12.8, 2 squirts, Injector opening time 0.92. Raise every cell with say 10% (percent, not points) to be on the rich side. Better to tune down on fuel than to tune up. As you're running a SC, you probably need more fuel over the entire range anyway.
Make sure you hook up that TPS (5V to 2I, TPS on 3E). Only one guy on this forum feels you can do without TPS and use the MAP sensor instead and he has a habit of insulting people .
Nothing wrong about asking a VE table. I'd call him smart to ask for one instead of just throwing in some random numbers and hoping it'll be ok.
Did your VE table became populated out of thin air? Or did someone else do it for you while you were crying for help?
He would be even smarter if he asked for a AFR table, but even then, he'd need the VE as well.
Try this with stock injectors, req fuel 12.8, 2 squirts, Injector opening time 0.92. Raise every cell with say 10% (percent, not points) to be on the rich side. Better to tune down on fuel than to tune up. As you're running a SC, you probably need more fuel over the entire range anyway.
Make sure you hook up that TPS (5V to 2I, TPS on 3E). Only one guy on this forum feels you can do without TPS and use the MAP sensor instead and he has a habit of insulting people .
Last edited by WestfieldMX5; 10-04-2009 at 07:20 AM.
Thread
Thread Starter
Forum
Replies
Last Post