engine runs good, idle still wacky (sucks)
#1
Elite Member
Thread Starter
iTrader: (6)
Join Date: Feb 2013
Location: A cave in Va
Posts: 3,395
Total Cats: 456
engine runs good, idle still wacky (sucks)
I was stoked to find hornetballs idle write up last night and was certain I had found my answer! followed the write up word for word and the end result was exactly what I have always had. An idle in the 40-50 kpa range. Just a small bit of throttle (1800rpm) and it comes down to 25-30 kpa. "It must be a vacuum leak" I said. proceed to spray the engine compartment with carb cleaner. nothing. spray it in the intake pipe and idle raises. clog the intake pipe with a t shirt and then search with carb cleaner for a leak again.Nothing.
No amount of timing in the low rpm range brings down the kpa. start @10* then work my way up to 30*(30 just to see, I know i should be 10-15)
All idle area cells are constant in timing and ve1 up to 1500rpm,idle still fluctuates 75-100 rpm and afr bounces back and forth 1 whole number.
With hornetballs settings, I have to turn the idle screw out 4 turns to get the idle in the 1000rpm range.
Help me please.
DIYPNP
tunnerstudio
Intake,exhintake, header
Engine timing set@10* then -10 use table in TS
AFR - do not incorperate, being used during all of this
Runs like a champ on the stock ECU
No amount of timing in the low rpm range brings down the kpa. start @10* then work my way up to 30*(30 just to see, I know i should be 10-15)
All idle area cells are constant in timing and ve1 up to 1500rpm,idle still fluctuates 75-100 rpm and afr bounces back and forth 1 whole number.
With hornetballs settings, I have to turn the idle screw out 4 turns to get the idle in the 1000rpm range.
Help me please.
DIYPNP
tunnerstudio
Intake,exhintake, header
Engine timing set@10* then -10 use table in TS
AFR - do not incorperate, being used during all of this
Runs like a champ on the stock ECU
#2
Elite Member
Thread Starter
iTrader: (6)
Join Date: Feb 2013
Location: A cave in Va
Posts: 3,395
Total Cats: 456
CurrentTune.msq
some of the maps may be nerdy now. At my wits end with the idle issue I started making frantic changes to see if I could get different results.
Anyone near central Va. willing to tune this thing?
some of the maps may be nerdy now. At my wits end with the idle issue I started making frantic changes to see if I could get different results.
Anyone near central Va. willing to tune this thing?
#4
Seriously? Two things:
"All idle area cells are constant in timing and ve1 up to 1500rpm,idle still fluctuates 75-100 rpm and afr bounces back and forth 1 whole number."
VE values shouldn't be all the same through 1500 because the engines VE is not the same which will cause your AFR's to fluctuate and so will your idle.
As far as your bad vacuum readings at idle, its a mechanical problem and no amount of ECU tuning is going to help.
"All idle area cells are constant in timing and ve1 up to 1500rpm,idle still fluctuates 75-100 rpm and afr bounces back and forth 1 whole number."
VE values shouldn't be all the same through 1500 because the engines VE is not the same which will cause your AFR's to fluctuate and so will your idle.
As far as your bad vacuum readings at idle, its a mechanical problem and no amount of ECU tuning is going to help.
#6
Elite Member
Thread Starter
iTrader: (6)
Join Date: Feb 2013
Location: A cave in Va
Posts: 3,395
Total Cats: 456
OK This makes sense.Before I started messing with the me yesterday, it was pretty solid. I just had the higher than normal kpA, reading. I also think I misunderstood the ve part of the instructions.
This engine has 180,000mi. Perhaps this 40-45kpa is just what I'm going to get at idle?
This engine has 180,000mi. Perhaps this 40-45kpa is just what I'm going to get at idle?
#7
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,675
Total Cats: 3,017
It could be, but you are right. That's a bit too high.
Sometimes vacuum operated components leak internally. Block each one of the little lines individually and see if they effect idle speed. You can do this quickly and easily by squeezing each one closed with some vice grips. It doesn't even involve removing them.
Sometimes vacuum operated components leak internally. Block each one of the little lines individually and see if they effect idle speed. You can do this quickly and easily by squeezing each one closed with some vice grips. It doesn't even involve removing them.
#12
Elite Member
Thread Starter
iTrader: (6)
Join Date: Feb 2013
Location: A cave in Va
Posts: 3,395
Total Cats: 456
Still messing with this idle issue. When I test the valve in attempt to tune closed loop, I can eventually kill the engine with a low enough #. coming down from 35, somewhere around 15 the idle falls so low that the engine will die. Any thoughts on that? it was my understanding that it should just stop affecting the idle, not stop the engine all together.
#13
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,508
Total Cats: 4,080
a few random thoughts from skimming this thread:
vacuum will increase if you increase the idle speed.
a leak pre-TB will not affect the MS...you can take the entire intake off and run an open TB.
you do not have a leak if you can stall the car by reducing the idle valve fully.
as far as the idle valve, I tune mine so at the lowest possible duty cycle, the idle drops to about 650-700RPM at the lowest. I do this so on cold days you can still maintain a typical 850-900RPM idle speed (since you less air when cold).
typically the idle valve duty for a 90-97 is working between 30-60%DC.
does hornetball even have "settings" for ms2? I thought his write up was for MS1?
vacuum will increase if you increase the idle speed.
a leak pre-TB will not affect the MS...you can take the entire intake off and run an open TB.
you do not have a leak if you can stall the car by reducing the idle valve fully.
as far as the idle valve, I tune mine so at the lowest possible duty cycle, the idle drops to about 650-700RPM at the lowest. I do this so on cold days you can still maintain a typical 850-900RPM idle speed (since you less air when cold).
typically the idle valve duty for a 90-97 is working between 30-60%DC.
does hornetball even have "settings" for ms2? I thought his write up was for MS1?
Thread
Thread Starter
Forum
Replies
Last Post
eddy1128
Miata parts for sale/trade
8
12-10-2015 05:34 PM
Motorsport-Electronics
ECUs and Tuning
0
09-05-2015 08:02 AM