All my jumpers are on the bottom... is that okay? Also that photo may have been before I added them.

definitely not in the photo. top or bottom bitch, whatever, that's personally preference ;)

did you see what i said about the s12c jumper?

This is what I have done:
https://www.miataturbo.net/attachmen...ine=1377099917
lol at my shitty solder job. the light makes it look worse.

ah. okay, that's what i saw. cool.

So I'm going to omit U6 and the c26-29 since I wont' be using the serial port at all. Hopefully this b works. Almost done. WIll find out how much I fail today.

Do you have a base map?

I haven't looked to find one. I'd imagine I will have trouble finding something for 1200cc injectors, dw300 and stock 1.6. But can probably adjust it enough to atleast get it started and tuning. Trying to figure out how to use this Jimstim for now, and figuring out what you mean by this syncing I need to do.

Okay it detected the MS3 over USB and says it has firmware 1.2 on it already. I guess the current is 1.2.3? It's flashing to that now. So far so good................

Uh also holy shit the westfield site is no more? Welp glad I just about finished this MS3x.

Also I'm using this for my msq: https://www.miataturbo.net/megasquir...-signal-69409/

A lot of errors since the firmware was older, so I still have to go through and set everything up for the most part.

Okay I have a red box on the bottom of TunerStudio that says "Not Ready" and no tach.

I have JP7 jumped, and 2.39v from the 2 pots, and 2&3 on the DIP switch are on.

What do?

Okay noticed that on the StimX injector A-D will flash in sequence once, and then Injector G LED stays lit. The Idle LED is also lit.

Okay small update. After removing the JP8 (it said it didn't matter if it was used or not, it came with it installed so I left it) the IGN G LED does not come on.

When I power on the JimStim INJ A-D flash in sequence and then nothing.

Not sure if anyone saw my question about q22/q23... but if I overheated those while soldering would this cause my issue? Or if there was a bridge? Those legs were so close it's hard to tell if solder is shorting the legs.

It's working bitches! Turns out you need to read the directions for the jimstim.

I'm back. So for my CAS... where do I wire those wires in to the MS? I am building a harness from scratch so I'm not just plugging in my stock wiring harness. I see the expander has a CAM input and the MS has an input as well.

I'm about to check out and see if it's clear on the wiring diagram which goes where. But if anyone just wants to save me some time and tell me what color wires go to which pin on the MS and expander I will be happy.

Crank is mainboard pin like 6. Cam is 32 on ms3x. The diagram I made that you have shows it... they are labeled.

I understood which pins for the MS the cam and crank go to. But since they both come from the CAS I was unsure of which of the 4 wires went to which pins. I see from the MS3x 90-93 1.6 harness wiring diagram of yours its:

Y/L - Pin 32 Cam IN - MS3x
W - Pin 24 Crank IN - MS mainboard (for some reason it says pin 25 on yours but the diagram shows pin 24)
B - Pin 1 Ground

Then:

W/R - Main Relay

i guess i'm unsure what your issue is.

There is no issue now. Although is there a reason you wrote pin 25?

i messed up? cam used to be on pin 25, im sure i was confused.

Your cat probably changed it when you weren't looking. Sabotage.

never! my cats love me. they leave me hairballs and dingleberries all over the house as gifts.