New timing Map
 

Jealous? ...it's big.

http://www.boostedmiata.com/gallery2...iii_timing.jpg

you have more timing at 230 than I do at 180 lulz. I need to start putting these det cans to good use and finally massage my timing map:giggle:

Thanx for the inspiration

Silly big :)

I'll be jealous when you get the MS3X module aswell ;)

Why do you run 17deg on overrun? for the childish pops and bangs?

I run at 170 and 205 kPa, so my 230 row really isnt tuned/needed.

It was suggested to me by y8s to try running the over run like that, i don't have any after fires or anything.

I might not wait for the MSX module, not sure, as I can just build in an extra fuel and spark circuits and be on my merry way. Now if someone can develop a SD card ribbon extension cable...I'll be all over that.

just buy a cheap sd card, and a cheap sd card reader.

-Open the card and gut it. Solder wires to the contacts (thin hookup wire)
-Glue card back together
-Terminate wire ends when cable is as long as you need.
-Open card reader
-Cut out all associated USB junk
-Route cable into spot where USB cable came into the enclosure
-Solder wires onto SD card slot
-Glue back shut

Alternatively, buy a SD card slot on digikey and solder the cable to that. Then just hotglue the pins so they can't contact each other and wrap it all in electrical tape.

I've done it before long ago. Basically makes a SD card extension cable. SD is just another serial protocol. Uses 2 contacts for RX and TX, and a few others for power, gnd, and sync.

thanks neo! you are awesome when you don't belittle me.

I've not seen any info on the MSIII daughtercard for controling 2 extra injector outputs, gorra link?

If it's possible like my MSII setup MS3X isn't really worth it for us unless you desperately need the outputs.

MS3 can run 8 injector drivers ;)

Wow! I do like the map, may try it since I can listen for det. Haven't bumped mine up yet.

I do wish I had 0.1* resolution though....

Yah, but it cannot run a 15 cylinder engine. :laugh:

Shutup woman! Get on my horse!

There I corrected your mistake.

you could possible run a v16 in batch!

Correct me if I'm wrong, but the MSX card just has the built in spark, squirt and relay circuits built in with an easy way to run them out the harness.

I'd need a way to fit two spark circuits and one injector driver circuit in my Proto area. I think I have all my spare outputs free so I can still run them easily through the db37.

Can I adapt the sequential fuel mod for the DIYPNP to my v3.0 board?

Thats not "silly" big
what has held me back from MS in the past is the poor resolution.
That will give you some good resolution for high vac and tip in that I feel is needed for a nice 'feeling' tune

Smart idea: Take a pin header with enough pins for your inputs/outputs and solder it to the proto area. Then take a piece or protoboard and make your circuit on it, and solder on female pin header. Put it into your pin header. Voila, extended proto area that fits inside the case.

well i might acutally see what protoboard i can fit that will slide into the case next to the new MSIII chip and make my own weakass expansion board.

this assume assumes im not too lazy to build a new standalone harness and acutally run wires to do sequential...

Well.....its warm outside now, so that throws you biggest excuse (<cry> its cold </cry>) right out the window.

yeah, well im in GA, so i have another.

Here is a little something I wrote just for you. Not including the .h file but it only contains one function. Its simple, basic c but its effective :)

#include "braineack.h"
#include <iostream>

char answer;
bool reply;

int main()
{
cout << "Is your name Braineack? Y=Yes / N=No";
cin >> answer;

reply = braineack(asnwer);

if(reply)
cout << "You are a lazy horse F-er";
else
cout << "You drive a miata, you're still gay";

return 0;
}