Shadow Dash MS for Android
#43
Senior Member
iTrader: (14)
Join Date: Oct 2006
Location: South East Florida
Posts: 677
Total Cats: 6
couple questions
I see the in the bluetooth adaptor's description this: Powered by Pin 9 or supplied power adapter
Are all MS using Pin 9 to power?
Packaging constraints under the dash are tight, and I will have to use a serial cable. This cable should work with MS2 and the bluetooth, right?
MegaSquirt Tuning Cable (DB9 Straight Thru) DIYAutoTune.com
I see the in the bluetooth adaptor's description this: Powered by Pin 9 or supplied power adapter
Are all MS using Pin 9 to power?
Packaging constraints under the dash are tight, and I will have to use a serial cable. This cable should work with MS2 and the bluetooth, right?
MegaSquirt Tuning Cable (DB9 Straight Thru) DIYAutoTune.com
#44
Don't know about every MS, but it works without modifications on my Reverant built MS2. That cable should be fine.
Took a little drive today and did some logging with Shadow Dash. Fantastic little app, works great and makes data logging a snap. First time I ever got a decent log to import into virtual dyno and actually remembered which gear was used for the pull.
Took a little drive today and did some logging with Shadow Dash. Fantastic little app, works great and makes data logging a snap. First time I ever got a decent log to import into virtual dyno and actually remembered which gear was used for the pull.
#45
couple questions
I see the in the bluetooth adaptor's description this: Powered by Pin 9 or supplied power adapter
Are all MS using Pin 9 to power?
Packaging constraints under the dash are tight, and I will have to use a serial cable. This cable should work with MS2 and the bluetooth, right?
I see the in the bluetooth adaptor's description this: Powered by Pin 9 or supplied power adapter
Are all MS using Pin 9 to power?
Packaging constraints under the dash are tight, and I will have to use a serial cable. This cable should work with MS2 and the bluetooth, right?
#47
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,178
Total Cats: 1,681
When I am out logging pulls and need to remember which gear I am in I hit the spacebar on my laptop the number of times for the gear I am in. That way when I pull up the log in MLV I can count the marks then know the which gear the next pull is in.
#51
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
I just installed the Shadow Dash APK and have not connected it to the car yet. I only have one dashboard, is this normal? Is there some way to get get the others in green or blue, or "make a new dash"?
#54
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,178
Total Cats: 1,681
Yup, I have oil temp via a gm coolant sensor in my oil pain going to a ms3x analog in, made the dash in tunerstudio and copied it to the tablet which works every bit as good as tuner.studio... Even shows my pwm out gauge that shows what duty cycle I'm sending to my fuel pump controller.
#56
Read dis: Megasquirt-3 MS3 Generic Sensor Inputs
its easy, though you want a 2.49k bias resistor, I'm using a 2.47k and its 'close enough' it seems.
its easy, though you want a 2.49k bias resistor, I'm using a 2.47k and its 'close enough' it seems.
#59
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
The idle is jacked when connected, but otherwise this is cool. It's nice to take a log on the phone, go upstairs and review it on the computer, make minor adjustments, save new MSQ to the phone, then get in the car for work the next day, load the tune, drive to work.