Where can I find the center connector for the MSPNP?
Thread Starter
Joined: Nov 2006
Posts: 15,442
Total Cats: 2,106
From: Sunnyvale, CA
Where can I find the center connector for the MSPNP?
I have a busted-*** '92 to swipe parts from, but I can't find the center connector. I want to hook up the KnocksenseMS and the LC-1 before I start the car next week.
Reply
0
0
Newb
Joined: Apr 2006
Posts: 16
Total Cats: 0
i've never got to post an rtfm post before but...
Pin Number Connection
1 through 8 Breakout header
9 Electronic boost control
10 Alternate O2 Sensor Input (for wideband o2)
11 Input for KnockSenseMS knock box
12 Launch Control Input
13 Clutch Switch connection for launch control
14 through 16 Not Used
Section four provides information on wiring up pins 1 through 8.
Note that this middle connector is unfortunately not yet available to us to include in the initial MSPNP shipments—we’ll be knocking $20 off the retail price to accommodate for this until we can stock them which we are working on. Until then, you should be able to grab this from MANY junkyard Mazda’s from around the same era (90-2002ish). You’re looking for the 18pin wiring harness connector, and you want to cut it off with some wire attached that you can tap onto. We have these on order and will have them as soon as possible—it’s all about the lead-times…
1 through 8 Breakout header
9 Electronic boost control
10 Alternate O2 Sensor Input (for wideband o2)
11 Input for KnockSenseMS knock box
12 Launch Control Input
13 Clutch Switch connection for launch control
14 through 16 Not Used
Section four provides information on wiring up pins 1 through 8.
Note that this middle connector is unfortunately not yet available to us to include in the initial MSPNP shipments—we’ll be knocking $20 off the retail price to accommodate for this until we can stock them which we are working on. Until then, you should be able to grab this from MANY junkyard Mazda’s from around the same era (90-2002ish). You’re looking for the 18pin wiring harness connector, and you want to cut it off with some wire attached that you can tap onto. We have these on order and will have them as soon as possible—it’s all about the lead-times…
Reply
0
0
Thread Starter
Joined: Nov 2006
Posts: 15,442
Total Cats: 2,106
From: Sunnyvale, CA
I know what the pins do, but I can't find the actual connector on my parts car. The manual says you can get one off any 90-02 Mazda, but I can't find one in any obvious place on my wrecked '92.
Reply
0
0
You can buy it from boomslang too. Or that onlinecomponents store. Do a search for '99 PNP harness on here, there was a thread with a couple stores that sell them.
DIY might carry them?
DIY might carry them?
Reply
0
0
Joined: Jun 2006
Posts: 29,085
Total Cats: 375
From: Republic of Dallas
I read something somewhere that said the connector did not go out with the first batch of kits, but its going to be / is available...I need one too. I'd rather just ******* buy on for $10, rather than go trolling though a junk yard or buying one online that may be the right one.
found it:
Until you find one, you can wire knocksense into the clt lead and watch the data logs / led for knock, and tune it more conservatively I assume.
I need to hook my **** up soon, maybe this weekend. This **** is hard to do in a hotel parking lot though. Where are you hooking up the knock sensor?
found it:
Note that this middle connector is unfortunately not yet available to us to include in the initial MSPNP shipments—we’ll be knocking $20 off the retail price to accommodate for this until we can stock them which we are working on. Until then, you should be able to grab this from MANY junkyard Mazda’s from around the same era (90-2002ish). You’re looking for the 18pin wiring harness connector, and you want to cut it off with some wire attached that you can tap onto. We have these on order and will have them as soon as possible—it’s all about the lead-times…
I need to hook my **** up soon, maybe this weekend. This **** is hard to do in a hotel parking lot though. Where are you hooking up the knock sensor?
Reply
0
0
Reply
0
0
Joined: Jun 2006
Posts: 29,085
Total Cats: 375
From: Republic of Dallas
Reply
0
0
Reply
0
0
96+ Miata's have them-- it's the 16pin connector (used in the middle). We've got them on order but we're still waiting. The pins have come in but the connectors aren't here yet...
__________________
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Reply
0
0
Joined: Jun 2006
Posts: 29,085
Total Cats: 375
From: Republic of Dallas
I've been home 9 days ince October 6th, 2006. I left for Katrina on 9/4/05 and I've been home what I estimate to be 36 days since then. I'm so ******* ready to order a 60" hdtv and sit on my *** to use tivo with my dog for a couple weeks.
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
Oct 26, 2018 11:00 PM
graexodus
Miata parts for sale/trade
5
Oct 26, 2015 01:48 PM
