Megasquirt 2 w/ harness, LC1 WBO2 w/ harness, 460cc injectors
05-04-2013, 10:01 PM
#1
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
Megasquirt 2 w/ harness, LC1 WBO2 w/ harness, 460cc injectors
My turbo project was brought to an end by an impending move abroad, so I'm selling what I've got so far:
Megasquirt 2 Extra V3 built by me to run in parallel on a '97, fully tested and working with harness - $450 shipped SOLD
- MS2 Extra build spec
- Wired for spark, fuel and idle control but wouldn't take much to convert to standalone.
- Fully tested, good sync at all revs.
- 4 injector drivers for sequential injection.
- Spark output modified to prevent startup pops and fried coils when updating firmware.
- Parallel harness wired for spark and injector control on a '96/'97, idle control from stock ECU.
- Full documentation of the build and a basic tune for a stock 1.8 will be supplied.
- Includes fully assembled and working JimStim.
- Includes serial/USB cable, various spare components and EBC modkit.
Innovate LC-1 wideband O2 sensor and controller, with harness - $120 shipped
- Only 200 miles or so on the sensor, working fine.
- Includes DIY harness to connect to gauge/aftermarket ECU/stock ECU - no CEL if you use this harness!
- All original wires, connectors, box etc. included. Wires all original length, just like new.
460cc RX-7 Injectors - $70 shipped SOLD
- I bought these from a forum member who claimed they were good, but I never fitted them and so I can't vouch for their performance. Will need new o-rings.
For more information on the LC1 harness and MS2 build, please see my thread here.
- MS2 Extra build spec
- Wired for spark, fuel and idle control but wouldn't take much to convert to standalone.
- Fully tested, good sync at all revs.
- 4 injector drivers for sequential injection.
- Spark output modified to prevent startup pops and fried coils when updating firmware.
- Parallel harness wired for spark and injector control on a '96/'97, idle control from stock ECU.
- Full documentation of the build and a basic tune for a stock 1.8 will be supplied.
- Includes fully assembled and working JimStim.
- Includes serial/USB cable, various spare components and EBC modkit.
Innovate LC-1 wideband O2 sensor and controller, with harness - $120 shipped
- Only 200 miles or so on the sensor, working fine.
- Includes DIY harness to connect to gauge/aftermarket ECU/stock ECU - no CEL if you use this harness!
- All original wires, connectors, box etc. included. Wires all original length, just like new.
- I bought these from a forum member who claimed they were good, but I never fitted them and so I can't vouch for their performance. Will need new o-rings.
For more information on the LC1 harness and MS2 build, please see my thread here.
Last edited by Benm; 05-16-2013 at 09:51 AM. Reason: Fixed typo
0
05-06-2013, 08:12 PM
#2
Junior Member
Join Date: Jul 2010
Location: oceanside,ca
Posts: 60
Total Cats: 0
would you take 400 shipped for the ms2
0
05-06-2013, 10:05 PM
#3
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
I'll drop to $450. There's over $500 in parts there and I just want to recover some of the cash I put into it, not my time.
0
05-06-2013, 11:42 PM
#4
Junior Member
Join Date: Jul 2010
Location: oceanside,ca
Posts: 60
Total Cats: 0
0
05-07-2013, 08:20 AM
#5
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
For a '94 standalone the only change should be to add in R4 and R7 to the main board (2.49kOhm 1% 0.25W resistors). These are the bias resistors for coolant temp and intake air temp. Other than that, as you say, the harness is the only thing that's different. The connectors and wires from my harness will be usable for that, I kept wires the same length as supplied by DIYAutoTune. I can throw in a spare DB37 too.
There's literally about 2 miles on it to check everything worked, plus a couple of hours in the garage setting it up.
There's literally about 2 miles on it to check everything worked, plus a couple of hours in the garage setting it up.
0
05-07-2013, 09:10 AM
#6
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
0
05-07-2013, 09:51 AM
#7
Junior Member
Join Date: Dec 2012
Posts: 105
Total Cats: 8
Im interested in the injectors, shipping to 60441?
0
05-07-2013, 10:37 AM
#8
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
0
05-07-2013, 10:40 AM
#9
Junior Member
Join Date: Dec 2012
Posts: 105
Total Cats: 8
I'll take them. Pm your paypal please
0
05-08-2013, 12:06 AM
#10
Junior Member
Join Date: Jul 2010
Location: oceanside,ca
Posts: 60
Total Cats: 0
ok sounds good let me check my bank real quick and see if my bills hit because i will buy it
0
05-08-2013, 12:13 AM
#11
Junior Member
Join Date: Jul 2010
Location: oceanside,ca
Posts: 60
Total Cats: 0
whats your paypal? 450 shipped right? and could you soldier in those 2 resistors please
0
05-08-2013, 12:34 AM
#12
Junior Member
Join Date: Jul 2010
Location: oceanside,ca
Posts: 60
Total Cats: 0
is the jimstim like the simulator board?
0
05-08-2013, 06:39 AM
#13
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
PM'd with PayPal. No problem to put the resistors in.
Yeah, the Jimstim is basically an advanced stimulator that can (amongst other things) simulate the Miata cam signal. All the documentation is online.
Yeah, the Jimstim is basically an advanced stimulator that can (amongst other things) simulate the Miata cam signal. All the documentation is online.
0
05-10-2013, 09:34 AM
#14
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
Megasquirt and injectors sold, wideband still available. Open to offers.
0
05-14-2013, 08:15 AM
#15
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
Price drop on the wideband
0
05-17-2013, 08:41 AM
#16
Newb
Thread Starter
Join Date: Jan 2013
Location: Charlotte, NC
Posts: 22
Total Cats: 0
Bump
0
Thread
Thread Starter
Forum
Replies
Last Post
