Originally Posted by Brendan B
(Post 1604825)
Had bad experience from seller which was addressed in a haphazard way. Please be advised
|
I got some of the first bars that were made way back when. Zero issues and they showed up in the advertised amount of time.
|
Matt has been very helpful to me over the last several years. Not only did I purchase 2 bars from him, he was helpful in how to build a front duct and his guidance on fender louvers and his pics were super helpful. I can't believe that one pain in the ass customer whose feathers were ruffled is making such a fucking issue to have contacted his employers. My approval of top notch seller and product :) Fully endorsed !!!
|
Just ordered and received a bar from Matt. Good communication and prompt shipping Welds and paint are solid. Can't wait to get this in with an oil cooler.
@matrussell122 Might consider a metal strip (with holes?) that over hangs the top bar that would permit mounting other elements...like ducting or oil coolers. |
My bar is awesome and even showed up painted in two different colors. +1
|
PM sent!
|
Originally Posted by Socals14
(Post 1607551)
Just ordered and received a bar from Matt. Good communication and prompt shipping Welds and paint are solid. Can't wait to get this in with an oil cooler.
@matrussell122 Might consider a metal strip (with holes?) that over hangs the top bar that would permit mounting other elements...like ducting or oil coolers. |
Originally Posted by matrussell122
(Post 1607805)
Check my build thread. I used rivnuts to secure my ducting to the bar. Rivnuts are plenty strong to mount both ducting and an oil cooler. You could even throw an extra little bit going to the oem hood latch bolt point and have a really secure spot for a cooler.
|
PM sent
|
Have lots of material primed and ready to go into production. If you want a bar now is the time to get one!
|
I will have a batch of bars ready to ship Friday and two of them are still un spoken for. $195 shipped CONUS and no wait time! Pm me to get yours!
|
Originally Posted by matrussell122
(Post 1610725)
I will have a batch of bars ready to ship Friday and two of them are still un spoken for. $195 shipped CONUS and no wait time! Pm me to get yours!
|
I have one bar ready to ship next day. Whoever wants to claim it.
|
PM sent.
|
Bump for those that still need a bar for a winter project!
|
Are any of these currently available? I sent funds on 11/22 and haven't heard anything back. Waiting patiently.
|
Originally Posted by ozbrock
(Post 1613274)
Are any of these currently available? I sent funds on 11/22 and haven't heard anything back. Waiting patiently.
|
Originally Posted by matrussell122
(Post 1613277)
PM sent
|
Three bars on the shelf ready to ship this week no lead time!
|
I really dig mine.
|
I reviewed a good bit of the thread, but I may have missed it, was there ever any interest in doing an aluminum version? I don’t need add’l room for cooling, but I would like to drop as much weight off the front as possible. Either way, it looks like this is the thing to do if the plan is to also cut the top of the core support so engine swaps can happen easily through the front, correct?
Thanks |
PM'ed
|
Here is my plan with these bars...thoughts welcome.
https://cimg9.ibsrv.net/gimg/www.mia...85f5f2c64d.jpg |
9 bars made and ready to be shipped out! Only 2 are spoken for so if you have been on the fence now is the time to order! $195 shipped CONUS
https://cimg7.ibsrv.net/gimg/www.mia...797f7fad10.jpg |
Any left for me? Pm-ing!
|
PM sent.
|
Just thought I would post an update on how I used this bar to add ducting.
https://cimg9.ibsrv.net/gimg/www.mia...6f10ecf345.jpg https://cimg0.ibsrv.net/gimg/www.mia...d71cdc9105.jpg |
I have one bar ready to ship out today
|
Originally Posted by Socals14
(Post 1617933)
Just thought I would post an update on how I used this bar to add ducting.
https://cimg9.ibsrv.net/gimg/www.mia...6f10ecf345.jpg https://cimg0.ibsrv.net/gimg/www.mia...d71cdc9105.jpg |
Looks like the stuff yard real estate signs are made out of
|
Coroplast or something short for corrugated plastic
|
Corflute - you can buy sheets of it at large hardware stores (eg. Bunnings in Australia)
|
Originally Posted by matrussell122
(Post 1619022)
I have one bar ready to ship out today
|
Going to a group buy format again and will be rolling batches of bars out in groups of 10. If you want in on this current batch send me a pm to get on the list.
|
Matt you should consider making tabs for splitter rods built right into the front bars
|
Originally Posted by matrussell122
(Post 1621227)
Going to a group buy format again and will be rolling batches of bars out in groups of 10. If you want in on this current batch send me a pm to get on the list.
|
singing up for this.
|
Originally Posted by Alejo_NIN
(Post 1621432)
singing up for this.
|
Originally Posted by CoralDoc
(Post 1621456)
I hope that you are not off-key ;)
then i re-read my post. |
Originally Posted by Alejo_NIN
(Post 1621476)
i'm "the fuck is this guy saying..."
then i re-read my post. |
PM's you!
Seen some good ideas here and its motivated me to setup the ducting and put this bar in at the same time |
I have 6 spots left on this batch of bars going into the mail tomorrow. If you want in on this batch now is the time.
|
PM’d you.
|
Sent money and PM'd you thanks
|
Originally Posted by matrussell122
(Post 1622215)
I have 6 spots left on this batch of bars going into the mail tomorrow. If you want in on this batch now is the time.
|
Originally Posted by stevos555
(Post 1621228)
Matt you should consider making tabs for splitter rods built right into the front bars
Did give me a chance to put more shitty welds on my car though. https://cimg9.ibsrv.net/gimg/www.mia...9b957f390f.jpg |
Any update on this batch that supposedly went out on the 20th? Have not received mine yet, wondering if anyone else did :bigtu:
|
Joshua Feingold I have sent you messages with no response and need a valid shipping address to get your bar out.
Everyone else who ordered a bar should be receiving it in the mail this week. Starting to build a list for the next batch of bars. Remember when you PM me make sure I have your name and a shipping address |
payment sent!
thanks! |
CORALDOCPLEASE GET ME VALID SHIPPING ADDRESES
|
|
Payment Recieved!
|
Originally Posted by matrussell122
(Post 1623171)
Payment Recieved!
lol i hate doing those, so i figure i give you time, people get busy but i'm glad i was able to make it!!!!! definitely want the bar, thanks! |
Originally Posted by matrussell122
(Post 1586928)
Waiting on pricing back from waterjet. Hoping they get back to me today or tomorrow.
|
Originally Posted by Downmented
(Post 1623417)
Did this ever happen?
A lot has been up in the air lately and with the ducting kit Ill look into a sheet of aluminum and what itll take to make them at work. Shoot me a pm and ill work on pricing and have some answers this week. As for anyone else if ducting is something you wanted send me a PM and collectively maybe we can get a run going. |
...I wish I would have found this thread 3 weeks ago...
|
received the bar and installed this weekend.
i still have engine bay paint left over, so i went ahead and hit it with a bit of car paint. single stage. also welded the seams that were left open when the front bar was removed. so awesome! https://i.ibb.co/2q6rpzj/IMG-5407.jpg https://i.ibb.co/rH86f78/824570-DB-4...1-B6-B8-B1.jpg https://i.ibb.co/Wy7RmLn/IMG-5414.jpg https://i.ibb.co/9YK4ZGg/IMG-5410.jpg https://i.ibb.co/H78Lhxj/IMG-5408.jpg |
Originally Posted by halfdemonpyro
(Post 1623742)
...I wish I would have found this thread 3 weeks ago...
|
An update for those wanting ducting. I have material and sourced and am just getting the files updated to send to the router. Then will be able to start getting kits together. Price is still TBD and the final product will need some fine tuning to work with each individual setup. That being said it is 95% of the way there.
|
Those waiting on bars: I am hoping to have some made in not much longer. My business partner and I have pieces cut and just need to chisel out some time to weld/paint/ship the current orders.
Here is a ducting update. I didn't really like my original design so am doing a minor revamp. I have material sourced and will be doing a test fit of this on my car then once its verified I will get a batch made up. https://cimg5.ibsrv.net/gimg/www.mia...74fac63b50.png |
All times are GMT -4. The time now is 04:20 PM. |
© 2024 MH Sub I, LLC dba Internet Brands