1. ryansmoneypit (ryan)
2. hornetball (rick)
3. turbofan (ed M)
4. Gee Emm (ed C)
5. Will Thompson
6. Daniel Payne
7. Steve stevos imprsn8
8. Joe Vance
9. Steve Card
10. rmeroda (Robin)
11. zellers88 (Dane)
12. gesso (geoff)
13. JoshEE
14. Doward
15. M2Ken
16. leboeuf
17. bahurd
18.
19.
20.


Three spots left!

 

1. ryansmoneypit (ryan)
2. hornetball (rick)
3. turbofan (ed M)
4. Gee Emm (ed C)
5. Will Thompson
6. Daniel Payne
7. Steve stevos imprsn8
8. Joe Vance
9. Steve Card
10. rmeroda (Robin)
11. zellers88 (Dane)
12. gesso (geoff)
13. JoshEE
14. Doward
15. M2Ken
16. leboeuf
17. bahurd
18. milkmandan
19.
20.

will be sending in used bushing for drilling.

 

Where's my billing email? I want to have my name all fancy and bold too!

 

Does that make you feel better?

1. ryansmoneypit (ryan)
2. hornetball (rick)
3. turbofan (ed M)
4. Gee Emm (ed C)
5. Will Thompson
6. Daniel Payne
7. Steve stevos imprsn8
8. Joe Vance
9. Steve Card
10. rmeroda (Robin)
11. zellers88 (Dane)
12. gesso (geoff)
13. JoshEE
14. Doward
15. M2Ken
16. leboeuf
17. bahurd
18. milkmandan
19.
20.

We will start billing tomorrow probably. Bold just means you for sure want one. There were a few people that we put on the list like 3 months ago lol.

 

Hey Sean, can you provide your insight into how hard the poly is to bore out?
I can make a holding/centering jig and have a drill press, but do I need anything crazy like a reamer and a lathe?
The only thing I really know is that drilling big holes in soft plastics can be a pita.
Not sure if this has been covered. I almost searched.

 

It is buried deep in the spherical thread and mega thread. But if you can hold it well without collapsing it, and have a sharp bit, it cuts ok, but you need a high rpm. I run my lathe at 1200rpm, no idea how 500ish or so would do. Freezing it also helps. Its not like plastic where it grabs and the bit wants to actually thread into the material, its quite the opposite, its doesn't want to cut, but instead deflects. Also if it starts to chatter, stop immediatly, it will open the bushing up much bigger than the bit.

Plastic drilling tip- knock the hugely positive rake of the drill bit down with a file or stone to make it neutral rake. (this goes for brass too)

 

Put me down for a set too. Will buy the bushings that need to be drilled new from you if you have any left...

1. ryansmoneypit (ryan)
2. hornetball (rick)
3. turbofan (ed M)
4. Gee Emm (ed C)
5. Will Thompson
6. Daniel Payne
7. Steve stevos imprsn8
8. Joe Vance
9. Steve Card
10. rmeroda (Robin)
11. zellers88 (Dane)
12. gesso (geoff)
13. JoshEE
14. Doward
15. M2Ken
16. leboeuf
17. bahurd
18. milkmandan
19. Junkwhale
20.

 

Let's button this one up

1. ryansmoneypit (ryan)
2. hornetball (rick)
3. turbofan (ed M)
4. Gee Emm (ed C)
5. Will Thompson
6. Daniel Payne
7. Steve stevos imprsn8
8. Joe Vance
9. Steve Card
10. rmeroda (Robin)
11. zellers88 (Dane)
12. gesso (geoff)
13. JoshEE
14. Doward
15. M2Ken
16. leboeuf
17. bahurd
18. milkmandan
19. Junkwhale
20. EO2K (Gordon)

Where do I send poly bushings?

 

Yay!!!! That was fast, thanks everybody!

1. ryansmoneypit (ryan)
2. hornetball (rick)
3. turbofan (ed M)
4. Gee Emm (ed C)
5. Will Thompson
6. Daniel Payne
7. Steve stevos imprsn8
8. Joe Vance
9. Steve Card
10. rmeroda (Robin)
11. zellers88 (Dane)
12. gesso (geoff)
13. JoshEE
14. Doward
15. M2Ken
16. leboeuf
17. bahurd
18. milkmandan
19. Junkwhale
20. EO2K (Gordon)

Gordon ill pm you later. Also let me know about this, you can send with bushings?

 

Sounds good, we can make that work

 

1. ryansmoneypit (ryan) paid
2. hornetball (rick)*
3. turbofan (ed M)
4. Gee Emm (ed C)
5. Will Thompson
6. Daniel Payne
7. Steve stevos imprsn8* paid
8. Joe Vance
9. Steve Card
10. rmeroda (Robin)
11. zellers88 (Dane)
12. gesso (geoff)
13. JoshEE
14. Doward*
15. M2Ken*
16. leboeuf*
17. bahurd*
18. milkmandan*
19. Junkwhale
20. EO2K (Gordon)

 

1. ryansmoneypit (ryan) paid
2. hornetball (rick)* paid
3. turbofan (ed M)
4. Gee Emm (ed C)
5. Will Thompson
6. Daniel Payne
7. Steve stevos imprsn8* paid
8. Joe Vance
9. Steve Card
10. rmeroda (Robin)
11. zellers88 (Dane)
12. gesso (geoff)
13. JoshEE
14. Doward*
15. M2Ken*
16. leboeuf*
17. bahurd* paid
18. milkmandan* paid
19. Junkwhale
20. EO2K (Gordon)

 

What are the asterisks for? shipping?

 

asterisks are for who has been contacted to pay. Everything is tracked outside of the forum. The lists you see are just for information for you all. (if that wasn't obvious)

 

My confidence level is rising

 

Also, a note about the predrilled FUCA bushings.

Energy suspension has a great system where you can't buy individual bushings, except in large amounts. And they aren't always cheap.

A set of pre-drilled fuca bushings is probably in the ~$40 range, and could be a month out.

If people are still interested please let us know and we will work to make it happen.

 

I think I may have posted this back in the original thread but Whiteline sells just the FUCA (W52208A) and the SadFab bushings slide right in. A little pricey but they are the correct size. I just opened up my package of them I ordered a while back and double checked before I posted this.

W52208A - Front Upper Control Arm Bushings - Inner Position - Whiteline Suspension Parts

 

That's awesome. Good find.

 

You yourself ordered those a year ago and they were on backorder for many many months.

 

I have memory issues.