FS: Fully PnP Megasquirt N Spark Extra V2.2 ECU for 96-97
03-29-2007, 12:38 AM
#1
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
FS: Fully PnP Megasquirt N Spark Extra V2.2 ECU for 96-97
I unfortunately will not be able to pay rent for next month, so my goodies have to go. Up for sale is a MSnSe V2.2 as a full plug-n-play setup for 96-97. Included is the ECU with all of the settings and maps currently running 029v, I will also supply the MSQ file. EasyTherm has already been set to use the Mazda CLT and a Ford IAT. An approximately 2ft wiring harness to install the MS right next to your stock ECU, and an extension harness for the OEM ECU where all you do is plug in the MS ECU harness. It is set up to run the OEM CLT sensor, and the appropriate bias resistor mod was done. The coil input and output mods were done following the DIYAutoTune website tutorial. A TIP120 was installed so that the Mazda idle valve can be used as well. I can also supply my wiring diagram for a 97 miata with appropriate pin colors and locations. Both the MS harness wires as well as the ECU extension harness wires are labeled. Here are pics:
So in summary, you'll be getting a MSnSe V2.2 ECU running 029v, the MS Harness all set up, and an OEM ECU extension harness, all set up. The mods are the input and output (ala diyautotune) for the 1.8l coils (spark settings have also been set as per NathanM-Ed's settings), TIP120 pwm mod, and OEM CLT bias resistor mod.
It'll take longer to put together a mounting setup next to the OEM ecu than it will to install the MS, ask me how I know
The entire system can be swapped from MS to OEM in a few minutes by just disconnecting and reconnected the insulated bullet terminals.
I'm asking 550 obo + shipping which should be around 10$ within the US via USPS Priority Mail. I'm in Los Angeles so local pickup is also available. I can take PayPal, but prefer not to because of their lame fees, personal checks will take a week to clear, and money orders or cash are always great.
So in summary, you'll be getting a MSnSe V2.2 ECU running 029v, the MS Harness all set up, and an OEM ECU extension harness, all set up. The mods are the input and output (ala diyautotune) for the 1.8l coils (spark settings have also been set as per NathanM-Ed's settings), TIP120 pwm mod, and OEM CLT bias resistor mod.
It'll take longer to put together a mounting setup next to the OEM ecu than it will to install the MS, ask me how I know
The entire system can be swapped from MS to OEM in a few minutes by just disconnecting and reconnected the insulated bullet terminals.I'm asking 550 obo + shipping which should be around 10$ within the US via USPS Priority Mail. I'm in Los Angeles so local pickup is also available. I can take PayPal, but prefer not to because of their lame fees, personal checks will take a week to clear, and money orders or cash are always great.
0
03-29-2007, 12:39 AM
#2
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
Also note the long purple wire on the MS harness is for your IAT since it'll be put under your hood.
0
03-29-2007, 12:46 AM
#3
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
Here's how I had it installed in my car before I connected the wiring:
0
03-30-2007, 09:05 PM
#4
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
Bump it up, taking offers as well.
0
04-01-2007, 08:24 AM
#5
Newb
Join Date: Mar 2007
Location: St. Thomas, USVI
Posts: 14
Total Cats: 0
please call me 541-663-6119
I cant send pm's yet...not enough posts
david
I cant send pm's yet...not enough posts
david
0
04-01-2007, 08:40 PM
#6
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
I'll take off 50$ if you don't want the 96-97 harness. I'll also take best offers.
0
04-03-2007, 02:36 AM
#7
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
How bout 500 for everything or 450 for the MS and MS wiring harness?
0
04-05-2007, 03:49 AM
#8
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
Bump, I need to sell this soon before my rent bill comes. I've had a lot of inquiries but no one has come through yet.
0
04-05-2007, 06:24 PM
#9
Newb
Join Date: Sep 2006
Posts: 21
Total Cats: 0
have you had this running in your car? Any problems? I may be interested.
0
04-05-2007, 06:43 PM
#10
Newb
Join Date: Sep 2006
Posts: 21
Total Cats: 0
I cant PM you, Call Me.
Mike 813-389-1340. If we can make a deal, I can wire you the cash.
Thanks Mike
Mike 813-389-1340. If we can make a deal, I can wire you the cash.
Thanks Mike
0
04-07-2007, 03:09 AM
#11
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
bump
0
04-10-2007, 09:21 PM
#12
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
Bump, I can sell the MS unit by itself for a reasonable price, give me an offer.
0
04-10-2007, 11:31 PM
#14
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
You'll just need to wire it in parallel with your stock ECU, I can take care of most of the megasquirt settings.
0
04-12-2007, 01:30 AM
#15
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
still available
0
04-15-2007, 05:03 PM
#17
Junior Member
Thread Starter
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
My MS has been sold! Thanks!
0
Thread
Thread Starter
Forum
Replies
Last Post
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM
