Retarded coolant line bending question
1 Attachment(s)
https://www.miataturbo.net/attachmen...ine=1362970676
So I'm stuck here. I have the manifold bolted up, the downpipe connected at the catalytic converter, and I can't really get any leverage to bend the fucking coolant pipe. Do I need to suck it up and take the manifold back off again so I can remove the pipe? Any recommended tool/method? I can't fit the downpipe with the coolant pipe where it is. |
Its just 1 nut on the exhaust manifold. Just pull it out of the mixing manifold and bend it to your hearts content.
|
Originally Posted by SKMetalworks
(Post 988080)
Its just 1 nut on the exhaust manifold. Just pull it out of the mixing manifold and bend it to your hearts content.
Argh, I just don't want to have to tighten that damn middle nut again |
Slide a deep socket over it with an extension in the socket and bend it, that'll give you some leverage. Or get a piece of pipe to slide over it or something. Shouldn't be that hard. Just don't kink it.
|
Well you only have a couple options.
1. Get a 6pack of can o man and a straw, suck it up and pull the tube off. 2. Cut the tube to clear downpipe 3. Pull off manifold which is what your going to do. The middle nut takes what 10 minutes to pull off? Do it once do it right. |
Originally Posted by albumleaf
(Post 988083)
Argh, I just don't want to have to tighten that damn middle nut again
|
The other alternative to pulling the manifold is pulling the mixing manifold from the side of the water pump. You'll have to replace that gasket, though.
|
Stick a 3/8" extension bar in the pipe for leverage and bend it where you need it.
|
I can pull that pipe out without removing my turbo/manifold...
|
Originally Posted by Savington
(Post 988094)
1.6-liter post.
Originally Posted by Braineack
(Post 988230)
I can pull that pipe out without removing my turbo/manifold...
I am seriously mechanically retarded, so thanks for putting up with this. |
If you can't bend that thing by putting a pipe over it and bending whatever direction you want, you seriously need to hit the gym for a day or a year or 10.
Seriously: its easy peasy. Just don't get carried away and kink it |
Sounds like he's saying that tab isn't coming off the stud to be able to pull it out of the mixing manifold.
OP, try manning the fuck up, see if that helps. |
I know my tube got stuck really well... in the mixing manifold. Practically put my fist through the fire wall once it finally broke free.
|
Originally Posted by curly
(Post 988245)
Sounds like he's saying that tab isn't coming off the stud to be able to pull it out of the mixing manifold.
OP, try manning the fuck up, see if that helps. you've been really feisty lately.. I love it. |
Use one of these bad boys jammed up against the manifold, and it'll make that pipe seem like it's made out of aluminum foil:
Craftsman 3Pc Screwdriver Pry Bar Set: Get the Greatest Tools at Sears |
Originally Posted by SJP0tato
(Post 988257)
Use one of these bad boys jammed up against the manifold, and it'll make that pipe seem like it's made out of aluminum foil:
Craftsman 3Pc Screwdriver Pry Bar Set: Get the Greatest Tools at Sears --Ian |
Originally Posted by 18psi
(Post 988243)
If you can't bend that thing by putting a pipe over it and bending whatever direction you want, you seriously need to hit the gym for a day or a year or 10.
Seriously: its easy peasy. Just don't get carried away and kink it I went to the gym on Friday for the first time since Aug. I did deadlifts, overhead presses, and pull-ups. My whole body is still sore, the weight was significantly less than I used to, and I feel feeble and impotent. |
So just like very other day of your life?
:giggle: |
yes. a shameful life.
|
I already hit the gym bro, I'm just a lightweight. Freeweight military press 150lb 3x10, weigh 150lb, 5"11 :v
|
All times are GMT -4. The time now is 06:59 PM. |
© 2024 MH Sub I, LLC dba Internet Brands