Is my swirl pot design okay?
#1
Senior Member
Thread Starter
iTrader: (4)
Join Date: May 2012
Location: Vallejo, CA
Posts: 541
Total Cats: 48
Is my swirl pot design okay?
I'm planning on building a swirl pot to mount next to the ABS unit. This will double as my new coolant fill location as well. Most of the pictures I see of swirl pots don't have the integrated filler neck, but instead have a nipple leading to a separate expansion tank which then leads to a reservoir. Would combining the two together have a negative effect? This is my design plan so far, any thoughts?
Last edited by FrankB; 09-30-2015 at 09:59 PM.
#4
Senior Member
Thread Starter
iTrader: (4)
Join Date: May 2012
Location: Vallejo, CA
Posts: 541
Total Cats: 48
Right now my radiator isn't the highest point in the system. I'd like to ensure that I am removing all of the air from the system. I already have all the materials to make it. I was just looking to make sure it wasn't flawed before I went ahead and started cutting materials.
#7
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,046
Total Cats: 6,607
Size would be my guess. We typically expect the expansion tank to have a fairly large capacity.
That said, you can buy little inline adapters from racing shops which have two radiator hose fittings and a cap / overflow line. Not a swirl pot, but an easy way to put fill / bleed at the highest point.
That said, you can buy little inline adapters from racing shops which have two radiator hose fittings and a cap / overflow line. Not a swirl pot, but an easy way to put fill / bleed at the highest point.
Last edited by Joe Perez; 10-02-2015 at 09:34 AM.
#8
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
Right now my radiator isn't the highest point in the system. I'd like to ensure that I am removing all of the air from the system. I already have all the materials to make it. I was just looking to make sure it wasn't flawed before I went ahead and started cutting materials.
#9
Senior Member
Thread Starter
iTrader: (4)
Join Date: May 2012
Location: Vallejo, CA
Posts: 541
Total Cats: 48
That's what I am trying to do with this design. Should I do something differently?
I'm using a 7" tall section of 4"OD aluminum pipe for the core. So capacity should be around 48oz. I thought of just using an inline fill cap like you mentioned but if I can make something better, then why not?
I have and use one of those radiator funnel kits and the cost of the airlift just isn't justified now that I don't work on cars for a living anymore.
I have all of the materials already just laying around, leftovers from other projects. It's just a matter of welding it all up.
Size would be my guess. We typically expect the expansion tank to have a fairly large capacity.
That said, you can buy little inline adapters from racing shops which have two radiator hose fittings and a cap / overflow line. Not a swirl pot, but an easy way to put fill / bleed at the highest point.
That said, you can buy little inline adapters from racing shops which have two radiator hose fittings and a cap / overflow line. Not a swirl pot, but an easy way to put fill / bleed at the highest point.
You could pick up this to fill the system and make sure there is no air in it, or one of the magic funnels.
I have all of the materials already just laying around, leftovers from other projects. It's just a matter of welding it all up.
#10
Senior Member
Thread Starter
iTrader: (4)
Join Date: May 2012
Location: Vallejo, CA
Posts: 541
Total Cats: 48
Since it would be my new fill point wouldn't I be able to achieve most of this at time of fill when using a radiator funnel and bringing the system to operating temp and letting it "burp"?
Thread
Thread Starter
Forum
Replies
Last Post
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM