Notices
DIY Turbo Discussion greddy on a 1.8? homebrew kit?

saving Stock rods by keeping peak torque low ?

Thread Tools
 
Search this Thread
 
Old Oct 16, 2012 | 12:58 AM
  #1  
AllSystemsNominal's Avatar
Thread Starter
Junior Member
 
Joined: Feb 2012
Posts: 85
Total Cats: 1
Default saving Stock rods by keeping peak torque low ?

Id really like to end up somewhere close to 240-250whp with my setup. its a stock 95 engine with good compression (180psi), Exhintake mod, GT2560r and I will be running MSpnp

its my understanding that the big killer of rods is torque is this correct ? my plan is to set the timing to keep peak torque low (210-220wtq) Assuming a good tune this should make it less likely that I will bend a rod right ??
Old Oct 16, 2012 | 03:05 AM
  #2  
Full_Tilt_Boogie's Avatar
Elite Member
iTrader: (1)
 
Joined: May 2009
Posts: 5,155
Total Cats: 409
From: Jacksonville, FL
Default

Yes torque, but also revs... and how much torque is being made at how high of revs... in other words, POWER.

A lot of bent rods are the result of detonation.
Old Oct 16, 2012 | 08:08 AM
  #3  
18psi's Avatar
VladiTuned
iTrader: (76)
 
Joined: Apr 2008
Posts: 35,821
Total Cats: 3,482
Default

Basically. Keep boost and timing down (but not low enough to melt stuff) to keep torque down. Also keep stock redline.
Old Oct 16, 2012 | 10:34 AM
  #4  
AllSystemsNominal's Avatar
Thread Starter
Junior Member
 
Joined: Feb 2012
Posts: 85
Total Cats: 1
Default

Yes was planning to rev it to 7k with a limiter set at 7100. I want to beable to beat on it pretty hard on the street. If I take it to the track boost will be lowered to the 190-200whp range
Old Oct 16, 2012 | 10:37 AM
  #5  
18psi's Avatar
VladiTuned
iTrader: (76)
 
Joined: Apr 2008
Posts: 35,821
Total Cats: 3,482
Default

A friend of mine runs 15psi on a large 16 with stock BP. Wastegate spring only, no boost controller. He absolutley rapes his car on the street every day, and its still just fine.

From my previous experiments, wastegate spring only is MUCH smoother onset from mbc. I think that's the difference between straight and gay rods.
Old Oct 16, 2012 | 11:01 AM
  #6  
concealer404's Avatar
Elite Member
iTrader: (3)
 
Joined: Aug 2011
Posts: 10,917
Total Cats: 2,206
Default

Originally Posted by 18psi
A friend of mine runs 15psi on a large 16 with stock BP. Wastegate spring only, no boost controller. He absolutley rapes his car on the street every day, and its still just fine.

From my previous experiments, wastegate spring only is MUCH smoother onset from mbc. I think that's the difference between straight and gay rods.
You know... i never really thought of that.

This is also why DISIs like to bend rods... it's the ridiculously fast spool up and sudden onset of torque that's the issue.

HRM.
Old Oct 16, 2012 | 11:30 AM
  #7  
thirdgen's Avatar
Slowest Progress Ever
iTrader: (26)
 
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
Default

Originally Posted by concealer404
You know... i never really thought of that.

This is also why DISIs like to bend rods... it's the ridiculously fast spool up and sudden onset of torque that's the issue.

HRM.
That's also why they blow ***** on fuel mileage.
Old Oct 16, 2012 | 08:57 PM
  #8  
AllSystemsNominal's Avatar
Thread Starter
Junior Member
 
Joined: Feb 2012
Posts: 85
Total Cats: 1
Default

What is DISI ?

my wastegate is a 7psi non adjustable unit. I guess when it comes time to up the boost maybe ill just get a new wastegate actuator

Last edited by AllSystemsNominal; Oct 16, 2012 at 10:44 PM.
Old Oct 16, 2012 | 09:52 PM
  #9  
DeerHunter's Avatar
Elite Member
 
Joined: May 2008
Posts: 2,059
Total Cats: 2,324
From: Canada
Default

Mazda's Direct Injection technology.
Old Oct 16, 2012 | 11:23 PM
  #10  
AllSystemsNominal's Avatar
Thread Starter
Junior Member
 
Joined: Feb 2012
Posts: 85
Total Cats: 1
Default

Originally Posted by 18psi
A friend of mine runs 15psi on a large 16 with stock BP. Wastegate spring only, no boost controller. He absolutley rapes his car on the street every day, and its still just fine.

From my previous experiments, wastegate spring only is MUCH smoother onset from mbc. I think that's the difference between straight and gay rods.

Its cars like your friends that make me want to run 250whp but then I hear of people bending rods making only 230whp/wtq

I see plenty of 250whp stock engine dyno graphs on this site but havent seen much talk about how long people have ran at that kind of power and with what kind of abuse
Old Oct 17, 2012 | 12:14 AM
  #11  
Full_Tilt_Boogie's Avatar
Elite Member
iTrader: (1)
 
Joined: May 2009
Posts: 5,155
Total Cats: 409
From: Jacksonville, FL
Default

^detonation

A street machine could probably make 300 without bending rods if there is absolutely zero detonation.

On the track youre building up so much heat, for such an extended period, that detonation can happen even with conservative boost and tuning. That why most well sorted setups are not even hitting 250 on a stock bottom end, and why shitty setups blow up way before that.

You never told us what you wanted to do with the car.
Old Oct 17, 2012 | 12:18 AM
  #12  
AllSystemsNominal's Avatar
Thread Starter
Junior Member
 
Joined: Feb 2012
Posts: 85
Total Cats: 1
Default

I like to beat on it pretty hard on the street and go out on curvy back roads and push it.

If I were to track it id lower the boost to get close to 200whp. I might even end up lowering the boost to that level when I go drive back roads since im pretty freakin hard on the car when I do that
Old Oct 17, 2012 | 12:25 AM
  #13  
thirdgen's Avatar
Slowest Progress Ever
iTrader: (26)
 
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
Default

Where is Paul when you need him...
All I can say is: stock block, gt2560, 18ish psi...319whp.
Old Oct 17, 2012 | 01:49 AM
  #14  
Boosted Escort's Avatar
Newb
iTrader: (1)
 
Joined: Jun 2010
Posts: 38
Total Cats: 1
Default

I made 280 whp with a holset hy35 on a stock BP until the oil pump blew. another guy on clubprotege made 300hp on a stock BP. he had an aem stinger with a good tune that motor lasted for two years and then the oil pump gears shattered. I could probably list a dozen who have been around 300whp with stock internals granted some of them didn't last that long. its all in the tune.
Old Oct 17, 2012 | 01:57 AM
  #15  
thirdgen's Avatar
Slowest Progress Ever
iTrader: (26)
 
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
Default

I could probably list 5 dozen people who claim they want 300whp, but have never ridden in a Miata with 240whp. 240whp is pretty damn fast.
Old Oct 17, 2012 | 02:12 AM
  #16  
Boosted Escort's Avatar
Newb
iTrader: (1)
 
Joined: Jun 2010
Posts: 38
Total Cats: 1
Default

I wasn't satisfied with 280whp it is never enough. I got used to it and it seemed slow. I wouldn't even worry about blowing it up with 250 lbs torque if you have a decent tune.
Old Oct 17, 2012 | 10:36 AM
  #17  
AllSystemsNominal's Avatar
Thread Starter
Junior Member
 
Joined: Feb 2012
Posts: 85
Total Cats: 1
Default

Originally Posted by thirdgen
Where is Paul when you need him...
All I can say is: stock block, gt2560, 18ish psi...319whp.
hasnt he been at that level for over a year ? dont know how much he drives or beats on the car though.
Old Oct 17, 2012 | 10:42 AM
  #18  
18psi's Avatar
VladiTuned
iTrader: (76)
 
Joined: Apr 2008
Posts: 35,821
Total Cats: 3,482
Default

I take that car/setup/numbers with a grain of salt. I'm not doubting the numbers, or the fact that its held up at that power level for a long time, but find me a handful of others that did the same: you won't find any more than 1 maybe 2. Which makes me think that car is the exception, not the rule.

Remember when leatherface made well over 300 and ran something silly like 27psi on stock block? Yeah, same thing.
Old Oct 17, 2012 | 10:54 AM
  #19  
concealer404's Avatar
Elite Member
iTrader: (3)
 
Joined: Aug 2011
Posts: 10,917
Total Cats: 2,206
Default

Originally Posted by 18psi
I take that car/setup/numbers with a grain of salt. I'm not doubting the numbers, or the fact that its held up at that power level for a long time, but find me a handful of others that did the same: you won't find any more than 1 maybe 2. Which makes me think that car is the exception, not the rule.

Remember when leatherface made well over 300 and ran something silly like 27psi on stock block? Yeah, same thing.
That car also made the smallest amount of power i've ever seen huffing that kind of boost.

Impressive that it held together... not impressive in the power it was (or wasn't) making.


There has been numerous Escort GT/Proteges in the past living for a relatively long period of time over 300whp on stock motors.


My Miata spent at least 50k miles over 250whp before i paid FM to tune it and they hamstrung it.
Old Oct 17, 2012 | 10:04 PM
  #20  
AllSystemsNominal's Avatar
Thread Starter
Junior Member
 
Joined: Feb 2012
Posts: 85
Total Cats: 1
Default

Originally Posted by concealer404
My Miata spent at least 50k miles over 250whp before i paid FM to tune it and they hamstrung it.
How did they F$%& things up ?



All times are GMT -4. The time now is 04:14 AM.