Jonathan's (buffon01) "Build"
#1
Elite Member
Thread Starter
iTrader: (9)
Join Date: Sep 2008
Location: Michigan
Posts: 5,609
Total Cats: 13
Jonathan's (buffon01) "Build"
Is time I started to put all this **** together. I’m going to have to do it by parts since this is my DD and I’m in a tight work and school schedule.
The car is a red 1991, stock engine, stock drive-train. The build specs are:
Garrett 2860
Flying Miata manifold and DP
Godspeed Inctercooler
Ebay universal piping
Ebay BOV
Braineack built MS
460cc Rx7 Injectors
F1 Six puck clutch
PLX 300M O2 WB.
This weekend I plan to finally and correctly install the MS. I have never set timing in a car before and if you’ll like to share some tips I’ll be glad to hear them. Actually any type of advise will be very welcomed.
I’ll try to install the turbo next weekend. However that depends on the amount of school work I get during the week. I plan to use the Begi tutorial/manual and guide. Like I said before any recommendations are welcomed.
The car is a red 1991, stock engine, stock drive-train. The build specs are:
Garrett 2860
Flying Miata manifold and DP
Godspeed Inctercooler
Ebay universal piping
Ebay BOV
Braineack built MS
460cc Rx7 Injectors
F1 Six puck clutch
PLX 300M O2 WB.
This weekend I plan to finally and correctly install the MS. I have never set timing in a car before and if you’ll like to share some tips I’ll be glad to hear them. Actually any type of advise will be very welcomed.
I’ll try to install the turbo next weekend. However that depends on the amount of school work I get during the week. I plan to use the Begi tutorial/manual and guide. Like I said before any recommendations are welcomed.
#4
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,192
Total Cats: 1,136
If you can't afford water/meth injection (understandable) then I'd suggest you keep a fairly low psi/hp tune, and go easy on the car. You'll break your rear end in no time. I purchased a 1.8 open diff, axles, and driveshaft for $160 total, which is a pretty good deal. Also, seach around here about that F1 clutch. It'll hold the power, but the bearings are considered junk, replace asap with oem units (pilot and throwout[release]).
#5
Elite Member
Thread Starter
iTrader: (9)
Join Date: Sep 2008
Location: Michigan
Posts: 5,609
Total Cats: 13
If you can't afford water/meth injection (understandable) then I'd suggest you keep a fairly low psi/hp tune, and go easy on the car. You'll break your rear end in no time. I purchased a 1.8 open diff, axles, and driveshaft for $160 total, which is a pretty good deal. Also, seach around here about that F1 clutch. It'll hold the power, but the bearings are considered junk, replace asap with oem units (pilot and throwout[release]).
Psi/tune, I hope to be able to safely get 200whp till I can get my hands on water/meth inj.
#7
Elite Member
Thread Starter
iTrader: (9)
Join Date: Sep 2008
Location: Michigan
Posts: 5,609
Total Cats: 13
Then it shouldnt be a problem given that I do everything right. Tyson, do me a favor link me to the seller you go your MBC from, and do you happen to have any pictures of your engine bay you could share?? I want to see how/where you put your bov ( I think we bought the same one )
#10
Elite Member
Thread Starter
iTrader: (9)
Join Date: Sep 2008
Location: Michigan
Posts: 5,609
Total Cats: 13
Nice is that a universal bend for the coolant inlet?? where did you get it??
On other issues I got the MS in the car I plugged everything where is supposed to go, jumped the FP. I connected my laptop to it and I dont any signal. The MS' middle light blinked the first time but not I get no response when I turn it on. Please help
On other issues I got the MS in the car I plugged everything where is supposed to go, jumped the FP. I connected my laptop to it and I dont any signal. The MS' middle light blinked the first time but not I get no response when I turn it on. Please help
#11
Senior Member
iTrader: (6)
Join Date: Aug 2008
Location: West Palm Beach, FL
Posts: 1,020
Total Cats: 1
that is a universal coolant straight/bendable hose connected to a 1.8 housing that replaced the mixing manifold.
everything is hooked up/plugged in?
no connections are broken on the harness?
do u have all the drivers installed for the cable/adapter if ur using one.
everything is hooked up/plugged in?
no connections are broken on the harness?
do u have all the drivers installed for the cable/adapter if ur using one.
#18
Elite Member
Thread Starter
iTrader: (9)
Join Date: Sep 2008
Location: Michigan
Posts: 5,609
Total Cats: 13
Yeah getting the fuel out is a bitch. I got most of it, I think. However my case is not even close to yours.
So what now?? I pulled the spark plugs and got most of the fuel out. I currently all the cavities where the spark plugs go open as well as intake inlet and the IAC.