Turbo Manifold question will this work?
#1
Turbo Manifold question will this work?
i have a TD05 Big16 turbo and my Manifold has heat cracks in it. i dont know what kind it is but i am losing power and it is quite noisy.its time to replace it. and without breaking the bank my car has been sitting for a while and ready to get my car running. i lack a few things like putting on my PNP MegaSquirt i had made 4 years ago by Braineack. and cant seem to get it to communicate with anything. Me and fellow turbo Miata Engineer friend last year tried and he has a hydra with no problems, i REALLY REALLY want this to work.and any help would be appreciated. anyway would this Manifold work on my car?? i tried to attatch its from ebay and its a cast iron Mani.. seems legit but will it work?
#2
With a t3 to eclipse td05 adapter it could work......as long as it the turbo doesn't hit the hood.
DSM TD05 T25 to T3 Adaptor Turbo Manifold Flange Adapter | eBay
DSM TD05 T25 to T3 Adaptor Turbo Manifold Flange Adapter | eBay
#3
Is this the listing? Cast Iron Mazda Mitata NA 1 6L T3 T4 Turbo Manifold Exhaust 35 WG Keep AC PW | eBay
If so, your turbo will not bolt directly to that if it is a Mitsubishi-flanged hotside (which is likely given your description).
If so, your turbo will not bolt directly to that if it is a Mitsubishi-flanged hotside (which is likely given your description).
#4
oh man..YESSSSSS. i really want this to work and have been doing some research on this but hopefully it wont hit my hood..any other suggestions i have been reading threads on this and i almost bought the CX racing glad i didnt..Megan racing has a combo pipe and Manifold still wondering about that one..any suggestions?
#5
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,178
Total Cats: 1,681
Do you have a megasquirt installed yet? How about a wideband O2 sensor? If those are done, stop screwing around with your ghetto setup and do things right. 1.8 swap to start. Then turbo correctly after that.
#6
What Lars said.
What about the downpipe? it is most unlikely the current one will fit with the t3+ td05 adapter set up.
Either way you are getting into custom fabrication...
You could get another short life ebay manifold?
It would be better to make a proper replacement.
https://www.miataturbo.net/diy-turbo...5/#post1173119
What about the downpipe? it is most unlikely the current one will fit with the t3+ td05 adapter set up.
Either way you are getting into custom fabrication...
You could get another short life ebay manifold?
It would be better to make a proper replacement.
https://www.miataturbo.net/diy-turbo...5/#post1173119
#7
i cant get the Megasquirt to communicate with my computer at all i downloaded the software i dont know if thats the problem or what..nothing. WB02 sensor working maybe i should do the 1.8 upgrade..everything is on car and running i am running a little rich i am very close..its been just so hard to finish and am having other little problems..going to get it..my mechanic friend that was a miata enthusiast helped me from the start its now been my project. i have alot on the car. Torzen, FM radiator, Hardtop, Comp Motor mounts, Exedy Clutch, Etc Etc
#9
my car has been sitting up unfinished for a coupla years..its almost heartbreaking seeing the moola i have put in this car. i have no garage to work on it..i can on weekends. i am about to take it over to my Ex brother inlaws and start slammin wrenches. he is a mechanical engineer and has built many a vehicles he has built stock cars and he is into big trucks like old blazers and ****...
#10
New pic of different set-up
so this is the only thing that will fit my current set-up? this is getting complicated as hell. unless i change my turbo to a different setup and manifold ,these parts are not interchangeable at all different mounting brackets etc etc. i am very limited to what i can do at this point correct?
Thread
Thread Starter
Forum
Replies
Last Post
AnotherDamnMiata
DIY Turbo Discussion
26
11-19-2015 11:34 PM