GT2860RS direct bolt-in replacement for GT2560 ?
#4
Elite Member
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
there is the typical 5 bolt and iirc the skyline bolt pattern.
they should be nearly the same with the difference of the 3" compressor inlet if you get a REAL 2860rs.
having had the 2860RS and a 2871 i would suggest going straight to the 2871. (if your open to suggestions, and if your going new)
they should be nearly the same with the difference of the 3" compressor inlet if you get a REAL 2860rs.
having had the 2860RS and a 2871 i would suggest going straight to the 2871. (if your open to suggestions, and if your going new)
#8
Elite Member
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
i have yet to get the 2871 dyno tuned, but it makes more power everywhere at the same boost level.
cars that i couldnt keep up to before i can now and from visual 4th gear pulls i make peak boost at identical rpm's on the same manifold
(however i did change from t2 flanged to the newer TiAL housing which means i had to hack off the t2 flange to weld the vband flange onto the tubular manifold)
cars that i couldnt keep up to before i can now and from visual 4th gear pulls i make peak boost at identical rpm's on the same manifold
(however i did change from t2 flanged to the newer TiAL housing which means i had to hack off the t2 flange to weld the vband flange onto the tubular manifold)
#10
Elite Member
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
0.86 AR hotside with iirc 62 trim 28rs wheels and 56 trim 71r wheels?
low end i dont think that i really lost any power... if i have it might have been 200-300rpm.
i know that i needed to retune my cells in boost at 3200-3700 the most which means that the turbo flows more in those cells and then there was ~4% more flow at the same map pressures for the remainder of the power cells. aka 3700-7100
low end i dont think that i really lost any power... if i have it might have been 200-300rpm.
i know that i needed to retune my cells in boost at 3200-3700 the most which means that the turbo flows more in those cells and then there was ~4% more flow at the same map pressures for the remainder of the power cells. aka 3700-7100
#12
Elite Member
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
go with that then.
if you have a nice manifold, some time and the funds, the TIAL hotside is (IMO) the reason my spool remained similar between the 2860 and the 2871 as thats literally the only difference between the setups.
the 2860 should flow enough even in the top end with a 0.64 that you shouldnt be noticing a power drop in the higher RPM since you have the AEM EMS and the nice boost control that it offers.
-Matt
if you have a nice manifold, some time and the funds, the TIAL hotside is (IMO) the reason my spool remained similar between the 2860 and the 2871 as thats literally the only difference between the setups.
the 2860 should flow enough even in the top end with a 0.64 that you shouldnt be noticing a power drop in the higher RPM since you have the AEM EMS and the nice boost control that it offers.
-Matt
Thread
Thread Starter
Forum
Replies
Last Post
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM