Stacy's 1hr Dyno Tune-Proven Power in Tampa
#1
Senior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Tampa
Posts: 780
Total Cats: 0
Stacy's 1hr Dyno Tune-Proven Power in Tampa
I went over to Proven Power today to see exactly how much my power my car was making. More importantly, how good of a tune that I actually had. I was hoping that after a full year of fiddling with the MS it would be ok. Surprisingly enough, I had a damn good tune. The AFR's on the 1st run were almost perfect through out the entire rpm range. We tweeked the fuel tables only when adding small amounts of boost, and I settled in on running 13.7 psi or 196 kPa, up from 12.5. It was still pulling hard to redline, and there was plenty of room left to go higher than that.
1st Run- 218.13hp / 199.85 TQ- 12.5 psi
8th Run- 242.38hp / 213.67 TQ- 13.7 psi
Enjoy.
1st Run- 218.13hp / 199.85 TQ- 12.5 psi
8th Run- 242.38hp / 213.67 TQ- 13.7 psi
Enjoy.
#9
Junior Member
iTrader: (1)
Join Date: Jun 2008
Location: San Diego, and Merced CA
Posts: 99
Total Cats: 0
Honestly power for me seems to peak around 6500rpm so when they asked if i wanted to increase decrease or leave the same rev limiter i said 7100 would be fine.
That being said when tuning we did peg the rev limiter to make sure we had full graphs of what was occurring.
That being said when tuning we did peg the rev limiter to make sure we had full graphs of what was occurring.
#11
Senior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Tampa
Posts: 780
Total Cats: 0
Brain, the turbo is very similar to your new china .60compressor .48 turbine, 50trim, I think.
Not running to redline is my fault. He asked where redline was and how far he wanted me to run it. I told him to shut it down around 6500. Hey, it was my 1st dyno pull with the MS so I was cautious. Next time I will let it go to the soft cut. I get nerved on the dyno, especially after seeing my buddies 951 blow out the bottom end a few years ago.
The downpipe sucks though. I already knew that going in. It bottlenecks from 3 to 2.25 then back up to 2.5. It is cobbled up mess. Also, the ext wastegate dump enters the downpipe real close to the turbine exit. They are going to fab me a new 304 SS downpipe with V band. It should help the spool considerably.
Outside of that, I am pleased.
Not running to redline is my fault. He asked where redline was and how far he wanted me to run it. I told him to shut it down around 6500. Hey, it was my 1st dyno pull with the MS so I was cautious. Next time I will let it go to the soft cut. I get nerved on the dyno, especially after seeing my buddies 951 blow out the bottom end a few years ago.
The downpipe sucks though. I already knew that going in. It bottlenecks from 3 to 2.25 then back up to 2.5. It is cobbled up mess. Also, the ext wastegate dump enters the downpipe real close to the turbine exit. They are going to fab me a new 304 SS downpipe with V band. It should help the spool considerably.
Outside of that, I am pleased.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM