extraction hood
#241
An extractor hood just popped up on D.C. craigslist if anyone is looking. The seller says it'll fit 94-95 with pop ups.
http://washingtondc.craigslist.org/n...489754646.html
http://washingtondc.craigslist.org/n...489754646.html
#242
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
awakening the thread for this:
http://www.ferraris-online.com/pages...E-550GT-107633
and for unrelated awesomenss:
http://www.ferraris-online.com/pages...E-550GT-107633
and for unrelated awesomenss:
#250
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,508
Total Cats: 4,080
http://www.carbontrix.com/vents.htm
18x10" extractor.
I've seen one on a DSM in person, they did a much better job, I'll probably cut out a hole and rivet the lip up underneath not just plopped on top. Then one day mold it in:
18x10" extractor.
I've seen one on a DSM in person, they did a much better job, I'll probably cut out a hole and rivet the lip up underneath not just plopped on top. Then one day mold it in:
#251
I guess there's no room to bitch about the miata hood bump when look at that dsm. They're screwed no matter what- it's all ugly. I'm seriously considering that piece. And then just doing a flat black stripe on the hood to disguise it... or make it look quasi-intentional. I build a template for the eBay fiberglass evo-esque extractor and if it's position as far forward on the hood as possible, the rear of the piece still intersects the base of the Miata hood bump.
#254
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,508
Total Cats: 4,080
I decided that 18" isn't wide enough. going to use a cheap *** universal wrx "style" scoop. flip it around and use it for the airfoil. I'll probably have to be creative like Ben with the bend to make it function, but I figure at 25" wide it's a better choice. It's 29" from light to light.
#257
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
I decided that 18" isn't wide enough. going to use a cheap *** universal wrx "style" scoop. flip it around and use it for the airfoil. I'll probably have to be creative like Ben with the bend to make it function, but I figure at 25" wide it's a better choice. It's 29" from light to light.
check out if there'll be turbulence on the trailing edge with it backwards. You might end up with a stagnation point at the opening where the flow curls back under the lip.
#258
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,508
Total Cats: 4,080
good point, can probably whip up walls that taper down to prevent this if it occurs, but $40 shipped > $110 shipped vs the carbontrix.
now go read my mrgtx post, follow the link, and e-thug.
now go read my mrgtx post, follow the link, and e-thug.
#259
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,508
Total Cats: 4,080
the extreme here is promising....
http://www.drivenvisions.com/cgi-bin...tegory_Code=HS
much easier to mold in vs the ebay one.
http://www.drivenvisions.com/cgi-bin...tegory_Code=HS
much easier to mold in vs the ebay one.
#260
the extreme here is promising....
http://www.drivenvisions.com/cgi-bin...tegory_Code=HS
much easier to mold in vs the ebay one.
http://www.drivenvisions.com/cgi-bin...tegory_Code=HS
much easier to mold in vs the ebay one.