NB exhaust on an NA?
02-20-2017, 12:18 AM
#21
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,210
Total Cats: 1,139
I actually searched for NB exhaust fitment on an NA, which dug up this thread. I'm throwing a stock NB exhaust on my NA to quiet it down.
Here's what I found:
1. Resonator didn't want to fit without hitting my PPF, so I straight piped that.
2. The hanger in front of the subframe is on the chassis on an NA, but it's on the front of the subframe on an NB, right above the front eccentric. It's attached to the resonator so cutting it out helped with that.
3. The single hanger on the driver side of the NB muffler is about 6" further outboard than the NA.
4. The two muffler hangers on the passenger side actually mate up, but my poor fitment (slash and weld) makes them fit...poorly. So I can't comment if they're correct if and when you actually spend time to fit it properly.
5. Small issue, but I think the NB bumper sticks out further than the NA, so the tip sticks a few inches further out. Looks a little funky.
I'll try to get pictures of all this tomorrow while it's still on the lift.
Here's what I found:
1. Resonator didn't want to fit without hitting my PPF, so I straight piped that.
2. The hanger in front of the subframe is on the chassis on an NA, but it's on the front of the subframe on an NB, right above the front eccentric. It's attached to the resonator so cutting it out helped with that.
3. The single hanger on the driver side of the NB muffler is about 6" further outboard than the NA.
4. The two muffler hangers on the passenger side actually mate up, but my poor fitment (slash and weld) makes them fit...poorly. So I can't comment if they're correct if and when you actually spend time to fit it properly.
5. Small issue, but I think the NB bumper sticks out further than the NA, so the tip sticks a few inches further out. Looks a little funky.
I'll try to get pictures of all this tomorrow while it's still on the lift.
Reply
2
2
03-06-2018, 12:00 AM
#26
Junior Member
Join Date: Apr 2016
Location: Green Bay, WI
Posts: 96
Total Cats: 18
I know this is old, but I'm not the one bumping it. I just put a NB exhaust on my NA. The 2 mounts by the tailpipe are really close, just beat them a little with a big hammer to line them up perfect. Use a universal hanger where the exhaust comes through the subframe. Then weld a hanger to the exhaust where it mounts by the rear of the transmission. I used stainless threaded rod and it helped adjust the exhaust side to side a lot.
Reply
1
1
06-05-2020, 01:09 AM
#27
Newb
Join Date: Jun 2012
Location: Baton Rouge, LA
Posts: 11
Total Cats: -3
I actually searched for NB exhaust fitment on an NA, which dug up this thread. I'm throwing a stock NB exhaust on my NA to quiet it down.
Here's what I found:
1. Resonator didn't want to fit without hitting my PPF, so I straight piped that.
2. The hanger in front of the subframe is on the chassis on an NA, but it's on the front of the subframe on an NB, right above the front eccentric. It's attached to the resonator so cutting it out helped with that.
3. The single hanger on the driver side of the NB muffler is about 6" further outboard than the NA.
4. The two muffler hangers on the passenger side actually mate up, but my poor fitment (slash and weld) makes them fit...poorly. So I can't comment if they're correct if and when you actually spend time to fit it properly.
5. Small issue, but I think the NB bumper sticks out further than the NA, so the tip sticks a few inches further out. Looks a little funky.
I'll try to get pictures of all this tomorrow while it's still on the lift.
Here's what I found:
1. Resonator didn't want to fit without hitting my PPF, so I straight piped that.
2. The hanger in front of the subframe is on the chassis on an NA, but it's on the front of the subframe on an NB, right above the front eccentric. It's attached to the resonator so cutting it out helped with that.
3. The single hanger on the driver side of the NB muffler is about 6" further outboard than the NA.
4. The two muffler hangers on the passenger side actually mate up, but my poor fitment (slash and weld) makes them fit...poorly. So I can't comment if they're correct if and when you actually spend time to fit it properly.
5. Small issue, but I think the NB bumper sticks out further than the NA, so the tip sticks a few inches further out. Looks a little funky.
I'll try to get pictures of all this tomorrow while it's still on the lift.
Are you doing oil paintings of the install? I have been checking back every day for over 3 years.
Reply
1
1
Thread
Thread Starter
Forum
Replies
Last Post
Saml01
Prefabbed Turbo Kits
7
04-07-2008 01:17 PM
