Anyone feeling a MS tuneing/help meet? (NE USA)
#1
Elite Member
Thread Starter
iTrader: (12)
Join Date: Jan 2007
Location: Hermosa Beach, CA
Posts: 2,573
Total Cats: 12
Anyone feeling a MS tuneing/help meet? (NE USA)
I know I need help with my MS, and im sure there ae others who could use it. So I thought it would be nice to have a meet with people who have/know how to use MS.
As for location, we should find a place thats in the middle of everyone, me and brgracer are in media, pa (south east corner of PA).
So hopefully some people could chime in, and maybe we could have like a meet/run on some backroads or whatever.
As for location, we should find a place thats in the middle of everyone, me and brgracer are in media, pa (south east corner of PA).
So hopefully some people could chime in, and maybe we could have like a meet/run on some backroads or whatever.
#2
Elite Member
iTrader: (21)
Join Date: Jun 2006
Location: Point Pleasant, NJ
Posts: 2,957
Total Cats: 2
wasn't there some guy that brought up this to do on any sunday in March? I think he even posted a poll to figure out which day was best.
I'm down. Anyone off Mondays? Otherwise a sunday when I'm not auto-xing
I'm down. Anyone off Mondays? Otherwise a sunday when I'm not auto-xing
#12
uego half installed.
here's how far i got:
uego gauge mounted, sensor in downpipe, stock o2 removed, power/ground wires done, uego 0-5v wire connected to pin 10 on mspnp center connector but not yet plugged in. uego in it's own seems to work fine, afrs seem to be a lot different than my lm1 though.
i keep reading over the manual but i keep getting confused, i don't know which lambda sensor in the configurator i'm supposed to use. aem linear, or aem non-linear....my uego manual does not specify.
here's how far i got:
uego gauge mounted, sensor in downpipe, stock o2 removed, power/ground wires done, uego 0-5v wire connected to pin 10 on mspnp center connector but not yet plugged in. uego in it's own seems to work fine, afrs seem to be a lot different than my lm1 though.
i keep reading over the manual but i keep getting confused, i don't know which lambda sensor in the configurator i'm supposed to use. aem linear, or aem non-linear....my uego manual does not specify.
#15
Elite Member
iTrader: (21)
Join Date: Jun 2006
Location: Point Pleasant, NJ
Posts: 2,957
Total Cats: 2
did you do the next steps?
4. Now you are going to need to edit your MSQ file. Otherwise, you will get an error saying that units do not match. Search for (line 586):
Code:
<constant cols="8" name="afrBins1" rows="8" units="Volts">
and replace it with
Code:
<constant cols="8" name="afrBins1" rows="8" units="AFR">
5. If you originally had AFR target defined in voltages, they will not appear correctly in MegaTune once you re-open your MSQ for editing. You will need to re-enter in the AFR target, but this time in AFR format instead of volts.
4. Now you are going to need to edit your MSQ file. Otherwise, you will get an error saying that units do not match. Search for (line 586):
Code:
<constant cols="8" name="afrBins1" rows="8" units="Volts">
and replace it with
Code:
<constant cols="8" name="afrBins1" rows="8" units="AFR">
5. If you originally had AFR target defined in voltages, they will not appear correctly in MegaTune once you re-open your MSQ for editing. You will need to re-enter in the AFR target, but this time in AFR format instead of volts.
Thread
Thread Starter
Forum
Replies
Last Post
chris101
Miata parts for sale/trade
5
02-19-2016 07:13 PM