Parallel install--no tach signal
#1
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Parallel install--no tach signal
microsquirt based DIYPNP running MS2 3.0.3i with sequential piggy card
Unit ran fine in standalone with 2.1.1b. I built a boomslang harness to run the MS parallel with the stock computer, upgraded the firmware, and installed the sequential card. I removed the opto and vr pulldown resistors as part of the parallel build. My boomslang harness tones out perfect.
The stock computer will still start the car, pig rich, and run it for a few seconds before the car stalls.
The stock computer with MS in parallel will not start the car. I have no rpm reading in tunerstudio and have no activity on the tooth logger. All other readings look correct. Tried both rising and falling edge.
On the 3-wire CAS pigtail, I have 5V, 12V, and ground like I'm supposed to.
Kind of stumped here, and a little frustrated. Car hasn't run in a month and I'm punchy because it's a gorgeous day today...
Suggestions?
Unit ran fine in standalone with 2.1.1b. I built a boomslang harness to run the MS parallel with the stock computer, upgraded the firmware, and installed the sequential card. I removed the opto and vr pulldown resistors as part of the parallel build. My boomslang harness tones out perfect.
The stock computer will still start the car, pig rich, and run it for a few seconds before the car stalls.
The stock computer with MS in parallel will not start the car. I have no rpm reading in tunerstudio and have no activity on the tooth logger. All other readings look correct. Tried both rising and falling edge.
On the 3-wire CAS pigtail, I have 5V, 12V, and ground like I'm supposed to.
Kind of stumped here, and a little frustrated. Car hasn't run in a month and I'm punchy because it's a gorgeous day today...
Suggestions?
#4
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
I am considering reinstalling the pulldowns and trying standalone again. It should work, but I'd have no idle valve control (no big deal) and no cooling fan control (no big deal if not run long).
Only problem is my stock harness' connector clips are becoming very unhappy with all this in and out.
Oh, I won't have alternator regulation either. I pulled that circuit out of the MS.
Only problem is my stock harness' connector clips are becoming very unhappy with all this in and out.
Oh, I won't have alternator regulation either. I pulled that circuit out of the MS.
#5
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,501
Total Cats: 4,079
Not sure how the DIYPNP acutally differs, but when i build a standalone or piggyback, the only difference in the board in the idle mod and AIT and CLT bias resistors. Everything else lies in the harness.
#8
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Yes, you're supposed to leave off the pulldowns in parallel.
I will go to a trigger wheel that overlays the crank if this is not successful. I wanted to make it work though, so other people could copy.
I will go to a trigger wheel that overlays the crank if this is not successful. I wanted to make it work though, so other people could copy.
#9
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,501
Total Cats: 4,079
All I do is cut the signal back to the oem ECU so it can't do anything with it.
So lets say I have spark A and B on pin 24 & 25 on the db37, I'll run them out the harness to the yellow connector on the boomslang to where they need to go, but I wont have a wire from the yellow connector back to the gray plug to plug back into the oem ecu...
I do it for the injectors as well.
So lets say I have spark A and B on pin 24 & 25 on the db37, I'll run them out the harness to the yellow connector on the boomslang to where they need to go, but I wont have a wire from the yellow connector back to the gray plug to plug back into the oem ecu...
I do it for the injectors as well.
#10
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Ok, well my install differs because I need the computer to read the signals to not throw codes.
Speaking of which. I reinstalled the pulldowns for opto and vr. Car will start and run for a few seconds. When it's running, it runs very well. I want to note that it has never started as easily as it does now. I don't know why it shuts off exactly, but I assume that it has to do with the stock computer not turning the fuel pump on after prime because...
I get codes
P1345 Cylinder Discrimination Signal from CMP Sensor
P0335 Crankshaft Position Sensor A Circuit
And the tach doesn't work.
So I assume the stock computer gets no signal from the motor, doesn't run the fuel pump, and doesn't run the tach.
So either I need to find different value pulldowns or I just need to give up using the stock sensors and install a trigger wheel.
I really want it to work off stock sensors, just to prove it can do so, but it might be smart to abandon it. Hmm.
Speaking of which. I reinstalled the pulldowns for opto and vr. Car will start and run for a few seconds. When it's running, it runs very well. I want to note that it has never started as easily as it does now. I don't know why it shuts off exactly, but I assume that it has to do with the stock computer not turning the fuel pump on after prime because...
I get codes
P1345 Cylinder Discrimination Signal from CMP Sensor
P0335 Crankshaft Position Sensor A Circuit
And the tach doesn't work.
So I assume the stock computer gets no signal from the motor, doesn't run the fuel pump, and doesn't run the tach.
So either I need to find different value pulldowns or I just need to give up using the stock sensors and install a trigger wheel.
I really want it to work off stock sensors, just to prove it can do so, but it might be smart to abandon it. Hmm.
#12
Senior Member
iTrader: (23)
Join Date: Oct 2009
Location: Chatsworth, SoCal
Posts: 948
Total Cats: 1
I am somewhat retarted when it comes to electronics, but can't both use the same signals? Esnetially running it in parallel not series. Thsi is why I would pay to have someome build me a board.
Have a great day,
Jared
Have a great day,
Jared
#13
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
It should work, but that doesn't mean it does.
I think I'll just use the trigger wheel. I'd be grateful to anyone who knows how to hook it up to the microsquirt and what changes to make in my .msq. It's a 2 wire sensor.
I think I'll just use the trigger wheel. I'd be grateful to anyone who knows how to hook it up to the microsquirt and what changes to make in my .msq. It's a 2 wire sensor.
#14
Hi Ben,
maybe you should ask Abe, how he has designed his circuit for the MS2 (pull-up values), because I am running this circuit in parallel with the stock ECU with no probs. I know it is different to Microsquirt, but as the stock ECU still sees the sensors - the pull-up values should be good.
Greets
maybe you should ask Abe, how he has designed his circuit for the MS2 (pull-up values), because I am running this circuit in parallel with the stock ECU with no probs. I know it is different to Microsquirt, but as the stock ECU still sees the sensors - the pull-up values should be good.
Greets
#15
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
The 60-2 wheel and pickup are installed. I believe it is a VR sensor, and it looks like I hook up the 2 wires to VR+ and VR- and don't use any pulldowns, use "toothed wheel" as my ignition set up and then enter the wheel's info in "trigger wheel settings".
I'll give that a shot.
I'll give that a shot.
#16
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
It's installed. I can see the teeth on the logger. Car acts like it wants to start, but it doesn't. Have fuel and spark.
Uggh.
Side note. Spark from the LS2 truck coils = OMG
Uggh.
Side note. Spark from the LS2 truck coils = OMG
#17
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Here's what it looks like now. You'll note that empty 100' spool of wire. That's on top of the wire that came with the kit + I've opened a second spool of 100' wire to run some extra leads from the motor to under the dash (extra grounds, triggers for individual coils, 2 wires for the new crank sensor)
New crank sensor
New crank sensor
#18
Hi Ben,
maybe you should ask Abe, how he has designed his circuit for the MS2 (pull-up values), because I am running this circuit in parallel with the stock ECU with no probs. I know it is different to Microsquirt, but as the stock ECU still sees the sensors - the pull-up values should be good.
Greets
maybe you should ask Abe, how he has designed his circuit for the MS2 (pull-up values), because I am running this circuit in parallel with the stock ECU with no probs. I know it is different to Microsquirt, but as the stock ECU still sees the sensors - the pull-up values should be good.
Greets
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM
JacksonRacingEngines
Engine Performance
10
09-10-2015 09:52 AM