Miatas For Sale

Welcome to Miataturbo.net   Members
Go Back   Miata Turbo Forum - Turbo Kitten is watching you test compression. > Performance & Tuning > ECUs and Tuning > MEGAsquirt
Reload this Page Tach and Idle valve
 
Register Forgot Password?

Welcome to Miata Turbo Forum - Turbo Kitten is watching you test compression.
Welcome to Miata Turbo Forum - Turbo Kitten is watching you test compression.


You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

TRENDING PICTURES

Reply
 
 
 
 
LinkBack Thread Tools

Old 01-28-2007, 02:00 PM   #1
Default Tach and Idle valve  
Junior Member
 
Join Date: Aug 2005
Location: Iowa
Posts: 338
Feedback: 0 / 0%
Total Props: 0
93 1.6 miata
MSII v.3 unassembled kit...

OK, i'm building the thingamabobber and first option...
Tach Signal: Hall effect or VR? I chose Hall optical, is this correct?

I don't understand IAC stepper, our engine isn't stepper right, ...

erm, C-12 is empty (tach signal?)

Oh and i caught a mistake (step 54 or 55), with the whole thing about Ford and Mazda,
i put in a 2.49k Ford resistor instead of the 2.2k Mazda for the sensor table, go figure, but
my question is would i have to de-solder this and use the correct one
or can this be recalibrated in MegaTune?
__________________
*93 1.6L - blk/white w/white hardtop IHI Turbo, Megasquirt+460's, Spec2 Clutch, Built Engine, Hard Dog, JRSways, DIY Port and Polish head. Clutch not engaging....
*93 1.6L - blk/white w/T25, Begi Mani/DP, Megasquirt+550's, COP's, Spec2 Clutch, BorlaDuals, Autopower, KYB, RBSways, 220whp.
Mouglie is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 01-28-2007, 04:04 PM   #2
Default  
Junior Member
 
Join Date: Aug 2005
Location: Iowa
Posts: 338
Feedback: 0 / 0%
Total Props: 0
I'm sorry if this was a stupid post, i just found my answers... i still don't know whats the deal with the IAC stepper...
Mouglie is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 01-28-2007, 04:28 PM   #3
Default  
Junior Member
 
Join Date: Nov 2005
Location: Down Under
Posts: 252
Feedback: 0 / 0%
Total Props: 0
Quote:
Originally Posted by Mouglie View Post
I'm sorry if this was a stupid post, i just found my answers... i still don't know whats the deal with the IAC stepper...
The big deal with the IAC stepper is that MSnSE won't control one. But as you said, we don't have an IAC stepper so it's not important.
Aussie Driver is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 01-28-2007, 05:06 PM   #4
Default  
Junior Member
 
Join Date: Aug 2005
Location: Iowa
Posts: 338
Feedback: 0 / 0%
Total Props: 0
Quote:
Originally Posted by Aussie Driver View Post
we don't have an IAC stepper
so what do we have?
Mouglie is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 01-28-2007, 05:14 PM   #5
Default  
Junior Member
 
Join Date: Nov 2005
Location: Down Under
Posts: 252
Feedback: 0 / 0%
Total Props: 0
We have a 3-wire Bosche IAC/ISC valve. If you do the PWM idle board mods then MSnSE will happily control the idle.
Aussie Driver is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 01-28-2007, 05:37 PM   #6
Default  
Junior Member
 
Join Date: Aug 2005
Location: Iowa
Posts: 338
Feedback: 0 / 0%
Total Props: 0
kool... i'll do the PWM mod...

but i just went back through the steps and
i skipped step 22... to make this quick, should i use
a gm sensor or what should i do in this step?

http://www.megamanual.com/ms2/V3assemble.htm

arhhh i see red letters, i don't wanna burn anything,
ok i got a MSII so that means i'm not burning anything right?
(i'll take a brake now)



thanks in advance...
Mouglie is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 01-28-2007, 05:51 PM   #7
Default  
Junior Member
 
Join Date: Nov 2005
Location: Down Under
Posts: 252
Feedback: 0 / 0%
Total Props: 0
Quote:
Originally Posted by Mouglie View Post
kool... i'll do the PWM mod...

but i just went back through the steps and
i skipped step 22... to make this quick, should i use
a gm sensor or what should i do in this step?

http://www.megamanual.com/ms2/V3assemble.htm

arhhh i see red letters, i don't wanna burn anything,
ok i got a MSII so that means i'm not burning anything right?
(i'll take a brake now)



thanks in advance...
Go with your first instincts on this one. Leave it skipped.
Aussie Driver is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 01-28-2007, 05:51 PM
 
 
 
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 

Advertising Information - miataturbo.net - Archive - Privacy Statement - Terms of Service - Top