Another DIY splitter/air dam installation
11-20-2011, 05:18 PM
#1
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
Another DIY splitter/air dam installation
So though I had considered doing something like this before, I was not ready to take the plunge until I saw Handy_Man's installation on this thread...
https://www.miataturbo.net/race-prep-75/home-made-splitter-air-dam-ducting-60291/
I really like the way his turned out so I decided right there to use the same approach to remake the splitter and air dam for my car. The splitter is made from 3/8" birch plywood, which I had left over from the first splitter I had made. The front air dam is made from 1/8" black ABS purchased from my usual supplier, a local sign shop. The ducting is made from black coroplast, also from the same sign shop.
Here is the finished result...
The new splitter with a hammer shown for scale.
Front view
Ducting is visible on the sides inside of the dam, and around the oil cooler
Small holes on the sides are for the brake ducts
Inside the right side wheel well
The splitter from underneath
Miataturboz needs moar dogz, fast onez.
Canards and kitties to be added later.
https://www.miataturbo.net/race-prep-75/home-made-splitter-air-dam-ducting-60291/
I really like the way his turned out so I decided right there to use the same approach to remake the splitter and air dam for my car. The splitter is made from 3/8" birch plywood, which I had left over from the first splitter I had made. The front air dam is made from 1/8" black ABS purchased from my usual supplier, a local sign shop. The ducting is made from black coroplast, also from the same sign shop.
Here is the finished result...
The new splitter with a hammer shown for scale.
Front view
Ducting is visible on the sides inside of the dam, and around the oil cooler
Small holes on the sides are for the brake ducts
Inside the right side wheel well
The splitter from underneath
Miataturboz needs moar dogz, fast onez.
Canards and kitties to be added later.
Reply
3
3
11-20-2011, 07:46 PM
#5
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
Thanks I am happy with how it turned out. With canards it should look better still. When I get it back on the ground I'll take some more pictures.
Spoolin, keep trying. There should be some places where you are at that sell it, like the sign shops. They might not know WTF ABS is since it is not something they would normally use, but if you talk them through it I'll bet they can order it from their normal plastics supplier. I went through this the first time.
If not, let me know and I can buy you a sheet and bring it to TWS. It is about $75 for a 1/8" x 4' x 8' sheet.
Spoolin, keep trying. There should be some places where you are at that sell it, like the sign shops. They might not know WTF ABS is since it is not something they would normally use, but if you talk them through it I'll bet they can order it from their normal plastics supplier. I went through this the first time.
If not, let me know and I can buy you a sheet and bring it to TWS. It is about $75 for a 1/8" x 4' x 8' sheet.
Reply
0
0
11-21-2011, 03:00 AM
#7
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
In my case the upper end of the turnbuckles are attached to an existing hole in the bumper via the same carabiner hooks you can see at the splitter end of the turnbuckle.
Reply
0
0
11-21-2011, 03:40 AM
#8
This is happening to my car this winter too - thanks for starting another thread. What did you use for the little 'L' brackets mounted to the splitter in the first picture? I was going to just slice up pieces of aluminum angle but what you did looks better/easier/lighter.
-h
-h
Reply
0
0
11-21-2011, 05:10 PM
#10
Elite Member
Join Date: Jul 2007
Location: Houston, TX
Posts: 3,203
Total Cats: 147
That looks super effective, very similar to Spoolins. Get ready to tune the rear grip because you just increased the front a butt load 
This year the flat front is the new hottness, next year...
This year the flat front is the new hottness, next year...
Reply
0
0
11-28-2011, 11:34 AM
#18
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
[IMG]
[/IMG]
The testing at the race track was successful. Here it is in action at Texas World Speedway on the NASCAR banking in Turns 3 and 4. I set my personal best lap time, about 1.5 seconds faster. There were a lot of other variables so I cannot attribute all of the speed to the new splitter and air dam. But they were definitely working. The aero balance of the car was great everywhere.
[/IMG]The testing at the race track was successful. Here it is in action at Texas World Speedway on the NASCAR banking in Turns 3 and 4. I set my personal best lap time, about 1.5 seconds faster. There were a lot of other variables so I cannot attribute all of the speed to the new splitter and air dam. But they were definitely working. The aero balance of the car was great everywhere.
Reply
0
0
