Aidan's loose oily bunghole actually runs a track lap
#181
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Also planning some heat management right now. I have sleeving around both oil lines and bought some sleeving for the water lines. I also got a sheet of adhesive backed heat shield I was going to try on the brake lines/Master cylinder.
These are the two things I got.
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
Also forgot to say this in the last post but big thanks to Oil Filter Service Co. in portland. At one point I probably had 250$ in fittings trying to find a combo that worked. They took all the ones I didn't need back and also helped all they could finding parts and helping me figured out everything I needed.
These are the two things I got.
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
Also forgot to say this in the last post but big thanks to Oil Filter Service Co. in portland. At one point I probably had 250$ in fittings trying to find a combo that worked. They took all the ones I didn't need back and also helped all they could finding parts and helping me figured out everything I needed.
#182
Nice work. Glad to hear that people are willing to help you out.
PS - I've tried the adhesive-backed Thermo-Tec stuff and a warning, the adhesive gets brittle under high heat and stops sticking. I haven't found anything (yet) that'll stay stuck and have had to resort to metal ties to secure heat wraps. YMMV
PS - I've tried the adhesive-backed Thermo-Tec stuff and a warning, the adhesive gets brittle under high heat and stops sticking. I haven't found anything (yet) that'll stay stuck and have had to resort to metal ties to secure heat wraps. YMMV
#183
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Nice work. Glad to hear that people are willing to help you out.
PS - I've tried the adhesive-backed Thermo-Tec stuff and a warning, the adhesive gets brittle under high heat and stops sticking. I haven't found anything (yet) that'll stay stuck and have had to resort to metal ties to secure heat wraps. YMMV
PS - I've tried the adhesive-backed Thermo-Tec stuff and a warning, the adhesive gets brittle under high heat and stops sticking. I haven't found anything (yet) that'll stay stuck and have had to resort to metal ties to secure heat wraps. YMMV
#185
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
I don't think I have. Is it in your build thread somewhere?
EDIT: I think I found it: https://www.miataturbo.net/build-thr...6/#post1182078
How is it attached? And what is it made out of?
EDIT: I think I found it: https://www.miataturbo.net/build-thr...6/#post1182078
How is it attached? And what is it made out of?
#188
Junior Member
iTrader: (1)
Join Date: Mar 2013
Location: Traverse City, Michigan
Posts: 138
Total Cats: 4
Props for jumping in to making the manifold and what not but holy cow i was going to comment that it looked like a beaver attacked your piping hahah small gaps are the key for tig welding. it will all come with time !! keep up the work!
#190
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,191
Total Cats: 1,135
I should be getting a chop saw in the near future, I might grab a flange and some pipes and see how cleanly I can tack together a weld-el manifold like this and send it off to you for final welding.
#191
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
That would be fun. Having my car torn apart in my buddies garage is pushing our friendship lol. But he likes this stuff just as much as me. Would probably only be ~50 for gas and filler.
I also plan on getting a tig next summer when I move back to town. You could come take your own shot at welding it.
I also plan on getting a tig next summer when I move back to town. You could come take your own shot at welding it.
#192
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Ed came over, said I had a misfire. Found a dead coil. Who knows how long its been like that :/ I don't know how I didn't notice it. Anyone local have an extra toyota cop?
#193
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Got everything installed. Took it for a test drive. It stumbled then started sounding funny. Sounded like a subby, but not in a good way lol. turbofan came by to check it out and suggested a misfire. I pulled the coils and plugs and coil #1 is dead. Here are some pictures of finishing it up.
O2 bung:
\
BOV:
Pretty sure my ebay valve doesn't work. Got a lot of compressor surge when it ran so I hooked up the integrated CBV on my turbo and it got a lot better. I actually really like the noise it makes. Subtle but definitely a bov noise. I also have a real Greddy in box that I will try out tomorrow. If its too loud then there will be a Greddy for sale again.
Whole setup pictures:
Bonus cat in box picture:
O2 bung:
\
BOV:
Pretty sure my ebay valve doesn't work. Got a lot of compressor surge when it ran so I hooked up the integrated CBV on my turbo and it got a lot better. I actually really like the noise it makes. Subtle but definitely a bov noise. I also have a real Greddy in box that I will try out tomorrow. If its too loud then there will be a Greddy for sale again.
Whole setup pictures:
Bonus cat in box picture:
#194
SadFab CEO
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
i know thats a bad spot to source vacuum/boost for other things, but im not sure if a BOV is as sensitive to fluctuations as a mega squirt. did you try a different source?
"ceiling ***** and snowflakes"
what is a ceiling ball?
and is that an end mill i see chucked in a drill?
(sorry for all the ninja edits)
"ceiling ***** and snowflakes"
what is a ceiling ball?
and is that an end mill i see chucked in a drill?
(sorry for all the ninja edits)
#195
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
I figured a BOV just needs to see a strong vacuum, and signal integrity wasn't an issue. When I sourced the integrated CBV off that source it worked perfectly. I might fiddle with it or just sell it here. Need a BOV?... Lol.
#198
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
i know thats a bad spot to source vacuum/boost for other things, but im not sure if a BOV is as sensitive to fluctuations as a mega squirt. did you try a different source?
"ceiling ***** and snowflakes"
what is a ceiling ball?
and is that an end mill i see chucked in a drill?
(sorry for all the ninja edits)
"ceiling ***** and snowflakes"
what is a ceiling ball?
and is that an end mill i see chucked in a drill?
(sorry for all the ninja edits)
#199
Supporting Vendor
iTrader: (1)
Join Date: Sep 2010
Location: Lake Forest, CA
Posts: 7,952
Total Cats: 1,005
Glad to see you found the misfire. I don't think it's been that way for very long, when you drove off from my house last Monday it sounded fine.
Should have more power once you've got all 4 cylinders on board
Should have more power once you've got all 4 cylinders on board
#200
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Pretty sure it happened literally 30 seconds into the first test drive. I hit boost and then suddenly it stuttered. I wish I had caught it earlier. Missed the junkyard by like 15 minutes.