|
I'm basically doing the same thing to mine right now.:bigtu: What's the shop charging for assembly and shouldn't you wait for their measurements before buying bearings?
|
Originally Posted by flounder
(Post 802151)
I'm basically doing the same thing to mine right now.:bigtu: What's the shop charging for assembly and shouldn't you wait for their measurements before buying bearings?
I ordered bearings based on the engine having low mileage and we can go from there. |
Alright - The machine shop will be finished this week or early next week. In the mean time I've ordered some items for the reassembly. Let me run this past you guys so I'm not missing anything.
Items Ordered: - Oil pan gaskets - Front and rear oil pan seals - Thermal intake manifold gasket - Rear main seal - Valve cover gasket - Thermostat - 180 degrees - NGK 4644 V spark plugs (1 set for break in, another for tuning) - Exhaust manifold gasket - GMB water pump with seals - Accessory belt - Rotella T 10-30 oil for break in - Oil pump seals Items to be ordered - GATES timing belt - Tensioner and idler pulley - Mazda OEM MLS Head Gasket What am I overlooking? |
5 Attachment(s)
Did a little detail work tonight since I have not gotten the block back.
I decided to wrinkle black my valve cover. I started out with a parts cleaner, then pressure washed it and I primed it with self etching primer. https://www.miataturbo.net/attachmen...ine=1323408571 The deal with Wrinkle black is to do think, multiple coats and very evenly. I used to paint professionally so an aerosol can is hard to mess up. https://www.miataturbo.net/attachmen...ine=1323408571 Gave it about 5 minutes between the three coats and then baked it. https://www.miataturbo.net/attachmen...ine=1323408571 She came out perfect. https://www.miataturbo.net/attachmen...ine=1323408571 https://www.miataturbo.net/attachmen...ine=1323408571 |
fucking sexi
good job |
Looks great, but isn't that a sealing surface for the VVT or whatever is opposite the oil cap?
|
Originally Posted by curly
(Post 804196)
Looks great, but isn't that a sealing surface for the VVT or whatever is opposite the oil cap?
|
honestly, i just find this thread and run out of bits to read :0
I wont get my MX till possibly Feb hopefully Jan as it sits awaiting some parts in UK just now then me to save some extra cash to fly home a drive it here to Finland. Meanwhile i have to digest you guys build threads. I am loving this car very very clean build philosophy i hope i can manage something along these lines once my old girl gets here. that wrinkle finish is the nuts! |
My new favorite build thread. Besides Fae's, his is funny. This one is sexy. Nice looking car, btw.
|
OP, I see you live in metro detroit, we should meet up in the spring and run em. :)
I live in livonia. :skid: |
4 Attachment(s)
Engine machine work complete. Starting the assembly tonight my fools:
I started with a clean checklist of items I'd need to complete the build and the engine torque specs on hand. A good torque wrench and organization is all it really takes to build an engine. I started by taping off the block and hitting it with a wire wheel. The hot tank cant clean up these iron blocks like you see with the aluminum ones. Then I applied a couple thick layers of VHT engine enamel. I went with black because I actually want this thing to look clean after 11 miles of use. This stuff dries quickly and provides a durable finish. https://www.miataturbo.net/attachmen...ine=1323924477 Next I inspected my rings- They were filed to spec at the machine shop and matched to each piston. The guys wrote 1,2,3,4 on each ring and seperated them into three different boxes - 1st, 2nd, oil boxes. Installing the rings is a snap, just lube everything up and install them with the openings offset, you might have your own offset pattern but it's typical to avoid the middle of the skirt and the wrist pin, then offset them as opposite from each other as possible. Then I installed one wrist pin lock and then the rod was installed using the wrist pin. I was given a set of micro polished wrist pins by a friend who works at Diamond Racing but the pin was too long and didn't allow the lock to seat completely. So I went with the stock CP wrist pin which was machined very well to begin with. Lube is important here too. The second wrist pin is snapped in- when you feel comfortable with the seating of the pin and first lock you're safe to move on. Some people use a tool to install the locks, I use my Ninja strength hands. https://www.miataturbo.net/attachmen...ine=1323924477 I kicked off the rod caps with a couple of light taps from a hammer with tape wrapped over the business end. The machine shop also numbered these for me because they are in matching sets to each rod with the bearings already installed. It's important to keep these matched sets- the parts were inspected and bored and line honed with this organization. It's important to make sure that the valve reliefs on the pistons are on the correct side if your piston is not identical on both sides. My CP piston spec sheet identified the intake side as -.195 and exhaust at -.150 so the bigger relief side is to the intake side of the motor. BTW your belts are always closest to #1 cylinder making the intake side to the left if you remembered what your engine looked like when it was complete! I set my piston skirts into the cylinders and took a break to update you kids. https://www.miataturbo.net/attachmen...ine=1323924477 https://www.miataturbo.net/attachmen...ine=1323924477 |
Man, I wish I knew how to put a motor together, then maybe I would actually put rods and pistons in mine this winter.
|
16 Attachment(s)
The rings must be offset from each other, you'll notice each ring has an opening when it's installed (Because they are a C shape) and it's best to offset these openings from each other. Usually you don't want the openings over the middle of the skirt or the wrist pin. That way if fuel or oil were trying to pass by it would have to travel a longer distance in order to escape.
After the rods were mounted with their locks installed and the caps removed, double checking that the rings were installed and offset. I pulled out the ring compressor tool and prepared the pistons for installation by applying some assembly lube to the cylinder walls and taping off the tops of each piston. My pistons are coated so it's best to protect the finish with a couple pieces of painters tape. https://www.miataturbo.net/attachmen...ine=1323958532 I took the ring compressor and pressed it flush against the deck around the piston. Used the supplied tool to tighten the ring compressor and it seamlessly pressed the rings into their ring lands. After checking to see if all of the rings were indeed compressed I proceeded to tap them in using a wooden hammer as an extension and a rubber mallet for the blunt force. They should easily slide in with a few easy taps. If you notice strong resistance there is a problem- check that your ring compressor has compressed each of the rings and that the piston is not cocked or bound up. https://www.miataturbo.net/attachmen...ine=1323958532 https://www.miataturbo.net/attachmen...ine=1323958532 Now that my pistons have been installed I pushed them about 1/2 the way down the cylinder and removed my protective tape (you can see it did it's job protecting these sexy slugs) Putting the pistons 1/2 way down should make for an easy install of the crank when I flip this thing over. https://www.miataturbo.net/attachmen...ine=1323958532 After I flipped her over I proceeded to install the oil jets. These are installed with a banjo bolt and some copper washers. These are torqued down at 105-156 inch lbs. https://www.miataturbo.net/attachmen...ine=1323958532 With my oil squirters installed and torqued, I set my bearings and thrust washers in place. The thrust washers are installed at the 4th main. Then I thoroughly lubed the bearings and my crankshaft contact surfaces. You'll know your bearings are in the right place because they have a hole in them that lines up with an oil feed hole in the main. https://www.miataturbo.net/attachmen...ine=1323958532 I had the crankshaft micro polished so she looks nice n shiny. A touch more lube and shes ready to set in. I took the rods and leaned them so that they would line up with my crank. 1-4 forward and 2-3 towards me. https://www.miataturbo.net/attachmen...ine=1323958532 I set the main caps on with their bearings + lube of course and then the rod caps in the same manner. A nice easy tap with a rubber mallet sets them pretty firm in place for the ARP hardware to be loosely installed. I snugged them up by jumping from bolt to bolt trying to get the clamp as evenly as possible but still not tightening them down with any force. https://www.miataturbo.net/attachmen...ine=1323958532 Everything looks good, she rotates nicely. I'll wait until tomorrow to torque this baby down. |
Very nice build! I plan on replacing my rods and pistons sometime next year. Your build is good reference.
|
I really like the step by step with pics!!!
|
Awesome work man. I am in Grand Rapids - what shop are you using for all of your machine work? I have been strongly considering building a motor over the winter, but I need to find a reputable shop. I figured there would be more places near Detroit.
|
Champion Performance. Good group of guys. I had a bit of a hook up but they were highly recommended by my performance parts distributor. I got the motor back in 2 weeks.
Champion Performance - +1 (586) 755-7400 24290 Sherwood Center Line MI 48015-2026 United States http://www.champion-performance.com/ Take a look at their site- they outline the high quality machinery they use. If you call them any time soon let them know that Bryan Spears told you to call. They will be interested in discussing your build even if you aren't ready to pull the trigger any time soon. |
Originally Posted by Dem768
(Post 806652)
After I flipped her over I proceeded to install the oil jets. These are installed with a banjo bolt and some copper washers. These are torqued down at 105-156 inch lbs.
|
Those pistons look way too pretty to hide indoors!
|
15 Attachment(s)
Made some serious progress tonight.
I installed the oil pump rear main seal, oil baffle and oil pick up. Before I mounted the new pan it had to be tapped for my existing oil return line. 1 - $39.50 drill bit and 1 - $8.95 tap later and I've got myself a hole. https://www.miataturbo.net/attachmen...ine=1324191416 After mounting the pan I flipped the block over and started to accessorize this thing. New water pump, alternator, power steering and AC pump were all installed. https://www.miataturbo.net/attachmen...ine=1324191416 Installed the oil filter assembly and my knock sensor. The hole for the KS needed to be tapped out in order to seat it properly. The block is from an NA car so the knock sensor hole was never used and had since filled with junk. https://www.miataturbo.net/attachmen...ine=1324191416 Ran into a bit of a hiccup when i went to mount my Crank angle sensor. The previous car didn't have a coil on plug setup so the CAS hole was never used. The hole never even had threading... https://www.miataturbo.net/attachmen...ine=1324191416 I was forced to drill and tap the hold out- everything went together nicely after that. https://www.miataturbo.net/attachmen...ine=1324191416 Slapped the head on, torqued her down and moved on to the timing. I lined up my timing marks, mounted the belt and installed the timing covers. https://www.miataturbo.net/attachmen...ine=1324191416 I then cleaned out my intake manifold and mounted her up using my new thermal spacer gasket. https://www.miataturbo.net/attachmen...ine=1324191416 There she is.. all in one piece. I installed my plugs and called it a night. https://www.miataturbo.net/attachmen...ine=1324191416 |
| All times are GMT -4. The time now is 03:52 AM. |
© 2024 MH Sub I, LLC dba Internet Brands