The Mazzder MX FIVE Build
11-11-2017, 01:39 PM
#122
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Yeah there is e85 in North Charleston so not really much of a drive on the weekend. Not sure if I trust the gm sensor. Would prefer a manual switching system.
Reply
0
0
11-11-2017, 03:28 PM
#126
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Well if I built the motor right I don’t see why I’ll have any issues. Alright contacting Andrew to get a pro opinion on this upgrade. Not looking to exceed 300hp on this...one day maybe 6speed or bmw tranny swap. Then we can do all of it!
Last edited by ysleem; 11-11-2017 at 03:49 PM.
Reply
0
0
11-12-2017, 07:43 PM
#127
Elite Member
iTrader: (1)
Join Date: Apr 2014
Location: SF Bay Area, CA
Posts: 3,079
Total Cats: 553
Thanks Vlad! Not quite yet, I did hit 25psi today, fuelable below 5800 or so. BOV reference still leaks out the valve stem, 2 different crap ones on order, if they don't work, a real Tial from ATP.
Reply
0
0
11-13-2017, 07:19 AM
#128
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Originally Posted by sonofthehill
Thanks Vlad! Not quite yet, I did hit 25psi today, fuelable below 5800 or so. BOV reference still leaks out the valve stem, 2 different crap ones on order, if they don't work, a real Tial from ATP.
Making good progress with wire “hidingâ€. Will post pics in a bit.
Reply
0
0
11-13-2017, 12:33 PM
#132
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
I think his intention is that for long term use it would be beneficial so ethanol does not break down hardlines or any tubing not rated for ethanol. I don't have any data to substantiate comments, but from what I read on here not a lot of people have had issues with E85 doing those things.
Reply
0
0
11-15-2017, 07:52 AM
#133
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Got a 1.8 exhaust manifold from Lars and plan on sandblasting it and some other items to be painted this weekend before it gets too cold out. I should be able to get things wired up also this weekend if all goes well then proceed to cleaning engine bay and prepping for paint! Might need a space heater any recommendations?!
Reply
0
0
11-16-2017, 09:03 AM
#134
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Tore into vvt harness I got and now I can cut in and make one splice by reusing connectors and wires instead of two splices on my 1.6 harness. Victory!
Reply
0
0
11-17-2017, 07:13 AM
#135
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
More progress!
Got my throttle body, IACV, intake manifold, water pump pulley, and exhaust manifold sandblasted. Got some paint on these and began test fitting. Also got my GM LS Coils with a harness for only $60! So I’ll be making a bracket for them! Anyone know if OEM plug wires fit miata?
Will be modifying harness today too! So exciting!
Got my throttle body, IACV, intake manifold, water pump pulley, and exhaust manifold sandblasted. Got some paint on these and began test fitting. Also got my GM LS Coils with a harness for only $60! So I’ll be making a bracket for them! Anyone know if OEM plug wires fit miata?
Will be modifying harness today too! So exciting!
Reply
0
0
11-21-2017, 08:53 PM
#137
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Replacement gaskets ordered, loom ordered, ngk bk7res ordered, about to order sadfab coils bracket and wire setup as soon as sean gets them in stock. Just need comp motor mounts and the hvac duct after you delete a/c and to keep heater function. Ordering some -8an fittings tomorrow from charleston rubber and gasket as well.
Reply
0
0
12-04-2017, 06:12 AM
#138
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Made solid progress this past week! Oil lines shortened and an fittings redone, fuel rail adapted, o rings changed on two injectors, fuel harness installed, turbo manifold studs replaced with shorter ones, remaining parts ordered except sad fab components.
Reply
0
0
12-29-2017, 09:34 PM
#139
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Well that's just about a wrap! Got coolant, oil, and air lines ran! Sad fab mount installed! I highly recommend it! Just need an alternator bracket and I'm in business! Next phase is to paint engine bay!
Last edited by ysleem; 12-29-2017 at 09:47 PM.
Reply
0
0
12-30-2017, 02:45 PM
#140
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2014
Location: Mount Pleasant, SC
Posts: 567
Total Cats: 7
Started tearing into engine bay to get the car prepped to power wash crud off of it and to degrease, sand,primer, and paint! Found motor mounts torn which explains a little but about why getting into gear has been tough. Making car have a manual rack as well for full race effect! Any thing Else I should do while undertaking this effort? Aka what am I missing?
Reply
0
0
