built 1.6 from Italy
12-02-2020, 05:56 AM
#1
Newb
Thread Starter
Join Date: Jan 2018
Location: Como Italy
Posts: 16
Total Cats: 18
built 1.6 from Italy
Long story short, here in Italy 1.8 engines are uncommon and the few you find cost more than a fully forged 1.6.
The car is used for drift and track days and sometimes mountain streets touge..
this is my third setup and after 4 years i can say that i learned 'buy cheap, buy twice.. or thrice' saying. (first setup was emanage-Td04 and second setup was me221-chinacharger).
This is my actual part list:
Me221 ecu
FF 640cc
Walbro 255lph
Toyota cop's
EBC
Kraken subaru 3 holes cast manifold
3" DP to backbox
10 litres FMIC
Coolant reroute
19 row oil cooler
B6 engine 100k miles that i'm going to build this winter
Wiseco 79mm 8.7:1 pistons
H.-Beam rods
ACL racing bearings
ARP main studs
ARP head studs
OEM head gasket
Boundary stage 1 72psi oil pump
Fluidampr
So i'd like to keep using my exhaust sistem and i need a subaru flanged turbo (to replace my actual td04hl-19t), what do you guys recomend? i have seen vf34 or td05/16g turbos that could take me to my target 320-350 whp or there are some ThaiCharger like ArashiDynamics that made some hybrid subaru flanged ball bearing gt2860-2867 for like 1000 bucks.. does anyone know the quality? are them total junk?
Actually i have a 1.6 lightweight 9 lbs flywheel and i need a new clutch, do i need to upgrade to 1.8 flywheel and clutch? any advice? lightweight or not? (i have never tried a non-lightweight one so no comparison..)
This is my first engine build so could you please say me what do i need to ask to the workshop? i like to go there with clear ideas, for sure i need to:
bore cylinder for the new pistons
resurface block and head
crank balancing
bearing measurament
full head cleaning and reassembliyng with new seals
anything else?
will update with pics and videos!
i'm sorry for my bad english, hope it isn't too annoiyng.
The car is used for drift and track days and sometimes mountain streets touge..
this is my third setup and after 4 years i can say that i learned 'buy cheap, buy twice.. or thrice' saying. (first setup was emanage-Td04 and second setup was me221-chinacharger).
This is my actual part list:
Me221 ecu
FF 640cc
Walbro 255lph
Toyota cop's
EBC
Kraken subaru 3 holes cast manifold
3" DP to backbox
10 litres FMIC
Coolant reroute
19 row oil cooler
B6 engine 100k miles that i'm going to build this winter
Wiseco 79mm 8.7:1 pistons
H.-Beam rods
ACL racing bearings
ARP main studs
ARP head studs
OEM head gasket
Boundary stage 1 72psi oil pump
Fluidampr
So i'd like to keep using my exhaust sistem and i need a subaru flanged turbo (to replace my actual td04hl-19t), what do you guys recomend? i have seen vf34 or td05/16g turbos that could take me to my target 320-350 whp or there are some ThaiCharger like ArashiDynamics that made some hybrid subaru flanged ball bearing gt2860-2867 for like 1000 bucks.. does anyone know the quality? are them total junk?
Actually i have a 1.6 lightweight 9 lbs flywheel and i need a new clutch, do i need to upgrade to 1.8 flywheel and clutch? any advice? lightweight or not? (i have never tried a non-lightweight one so no comparison..)
This is my first engine build so could you please say me what do i need to ask to the workshop? i like to go there with clear ideas, for sure i need to:
bore cylinder for the new pistons
resurface block and head
crank balancing
bearing measurament
full head cleaning and reassembliyng with new seals
anything else?
will update with pics and videos!
i'm sorry for my bad english, hope it isn't too annoiyng.
Last edited by Carlo Joll Negri; 12-04-2020 at 10:08 AM.
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
