Added to the GM coil thread.
The table just allows you to get closer to the correct GM figures. Since the penalty for overdwell is ultra-catastrophic, you want to be as close as possible to the GM figures (I am slightly under them everywhere - I rounded down at all times during my conversion calculations). I am at 1.0ms discharge, I've seen references that GM uses 2.0ms. I may go up to 2ms since I have the room to do so. Dwell + discharge x2 can never exceed cycle time, but I'm well under that limit right now (~17ms at 7000rpm). |
Originally Posted by aidandj
(Post 1380085)
:
You should add those tables to the LS coil thread. For future reference. I added a cross-reference to Savington's #373 post in the https://www.miataturbo.net/megasquir...rection-86602/thread since I'd posted questions in there regarding these values and it will help future forum "Search"es (can never have enough cross-references). |
Decided to just go with the Radium connectors for simplicity. By the time I source PTFE-insulated wire in a small quantity, the bulkhead connector, the upper connector, the fuel pump connector, pins, and a crimper for everything, I would have been way over the ~$135 they charge anyway.
Also sent my headlights off to 18psi for refurb and blackout and picked up a Morimoto 4500k HID setup. |
They are gross lol. But you did warn me. The real question: how in the world did you manage to get so much sand/dirt into them? Sounds like a salt shaker when shook
https://cimg9.ibsrv.net/gimg/www.mia...60c0077964.jpg https://cimg1.ibsrv.net/gimg/www.mia...a0cc361685.jpg https://cimg2.ibsrv.net/gimg/www.mia...e55e0df67d.jpg https://cimg0.ibsrv.net/gimg/www.mia...7803447e78.jpg https://cimg6.ibsrv.net/gimg/www.mia...6922bc661d.jpg https://cimg7.ibsrv.net/gimg/www.mia...f79610b42e.jpg https://cimg8.ibsrv.net/gimg/www.mia...74eca2b256.jpg https://cimg3.ibsrv.net/gimg/www.mia...12d87f6898.jpg |
Yes, the horrible raccoon-eye trim from the 02SE left all sorts of nasty goo all over them. I may have gotten some of the dust/dirt in there during disassembly. The 15x10s require removal of a lot of the fender liner, so the engine bay is pretty messy in general.
|
Originally Posted by Savington
(Post 1380510)
Decided to just go with the Radium connectors for simplicity. By the time I source PTFE-insulated wire in a small quantity, the bulkhead connector, the upper connector, the fuel pump connector, pins, and a crimper for everything, I would have been way over the ~$135 they charge anyway.
|
Originally Posted by Savington
(Post 1380510)
Decided to just go with the Radium connectors for simplicity.
Edit: Dangti! :vash: I was hoping you knew something I did not. |
Originally Posted by Savington
(Post 1380750)
And back to the drawing board. The top connector is 2" tall plus clearance for the wire, which won't fit under the fuel tank cover. I need a 90deg setup.
--Ian |
Originally Posted by Savington
(Post 1380750)
And back to the drawing board. The top connector is 2" tall plus clearance for the wire, which won't fit under the fuel tank cover. I need a 90deg setup.
|
I actually have this idea in my head for a milled aluminum tube thing flat face on one side, like a tank turret with the wiring connector sticking out the side as the barrel. Drill a 1" hole in the top of the lid, bolt and seal this thing to the top and have the wires feed out at 90°. It would create another point of failure because this thing would need to seal to the top of the tank, and you would have to get creative drilling out some sort of hole pattern in the lid and then run the bolts up from inside the lid.
Bah! Probably too much work, like most of my crazy ideas. |
There are actually a few good solutions that just pass wires through, but fluid will wick up through the wires and wreak havoc on things. It has to be a pinned or soldered connector.
|
Oh yeah, I know it's something we've discussed at length in one if the other threads.
The aluminum thing I talking about would have a mount for one of these appropriate connectors, a simple round hole for something like the Radium or a 'D' hole for the Racetronix/GM style connector. If you were willing to strip down a lid I would imagine the 'D' style hole would be trivial to machine, the challenge would be holding the lid in the mill ;) |
I'm unhappy with my solution. But it was the best I could come up with after way too many hours of searching.
Racetronix sells a version of the GM style one. That seemed kind of close to the miata size. But it needs some lip to hold it in or something. And don't use any of the racetronix provided heatshrink/wire/anything. Mine all fell apart in regular gasoline after like 3 weeks. It was really bad. Bare wires in the gas tank because of it. PTFE heat shrink only. |
Originally Posted by EO2K
(Post 1380776)
I actually have this idea in my head for a milled aluminum tube thing flat face on one side, like a tank turret with the wiring connector sticking out the side as the barrel. Drill a 1" hole in the top of the lid, bolt and seal this thing to the top and have the wires feed out at 90°. It would create another point of failure because this thing would need to seal to the top of the tank, and you would have to get creative drilling out some sort of hole pattern in the lid and then run the bolts up from inside the lid.
Bah! Probably too much work, like most of my crazy ideas. --Ian |
Originally Posted by codrus
(Post 1380814)
Don't do it. The guy who built the Locost I owned had made a fuel tank out of aluminum and then hacked up the Mazda pump/mount/assembly thing to go on top. I never did get it to fully seal before selling the car and letting it become the new owner's problem.
--Ian |
I think the best solution for high amp into the tank is the bulkhead studs.Like this. I really admit defeat coming to this because its so kludgy but its like the only safe solution. I think the best answer is really a carb motor high flow low pressure pump in the tank feeding a small surge tank with an outside the tank pump so you dont have to deal with that shit.
https://cimg3.ibsrv.net/gimg/www.mia...81b5935240.jpg |
Originally Posted by Savington
(Post 1379719)
This is a dumb question, in either case the flyback diode goes after the fuel pump. I believe the flyback diode protects the SSR, though, since the stock FP circuit doesn't use one, and my engineer friend confirmed this.
A 1N4007 (1A rating) is way too small for fuel pump currents (>10A). You will need something beefy like this (20A), and with a small heatsink to boot: VS-20TQ040PBF Vishay Semiconductor Diodes Division | Discrete Semiconductor Products | DigiKey I have some on hand. The 1N4007 is only good enough for injectors and solenoids. Actuallly an SB540 is a much better choice. Gets less warm. It makes the response of my VVT solenoid much more linear wrt applied duty cycle. The diode needs to be wired across the fuel pump, with the cathode on the + end of it. |
Originally Posted by Leafy
(Post 1380834)
I think the best solution for high amp into the tank is the bulkhead studs.Like this.
O-Ring seals and everything: https://www.efihardware.com/images/4...inals_4937.jpg https://www.efihardware.com/images/4...inals_4936.jpg $11.25/ea USD from Australia. Might leak past the threads unless you use the Hylomar (or some other E85 stable sealant) as listed in the PDF https://cimg8.ibsrv.net/gimg/www.mia...fedefd38e8.jpg |
Originally Posted by JasonC SBB
(Post 1380855)
Oh my, anything power electronics, ping me.
A 1N4007 (1A rating) is way too small for fuel pump currents (>10A). You will need something beefy like this (20A), and with a small heatsink to boot: VS-20TQ040PBF Vishay Semiconductor Diodes Division Discrete Semiconductor Products DigiKey I have some on hand. The 1N4007 is only good enough for injectors and solenoids. Actuallly an SB540 is a much better choice. Gets less warm. It makes the response of my VVT solenoid much more linear wrt applied duty cycle. The diode needs to be wired across the fuel pump, with the cathode on the + end of it. This is just my interpretation, is this not correct? |
Originally Posted by EO2K
(Post 1380859)
I like this one, it looks a lot more legit: https://www.efihardware.com/products...head-terminals
O-Ring seals and everything: https://www.efihardware.com/images/4...inals_4937.jpg https://www.efihardware.com/images/4...inals_4936.jpg $11.25/ea USD from Australia. Might leak past the threads unless you use the Hylomar (or some other E85 stable sealant) as listed in the PDF https://cimg8.ibsrv.net/gimg/www.mia...fedefd38e8.jpg |
All times are GMT -4. The time now is 07:06 PM. |
© 2024 MH Sub I, LLC dba Internet Brands