1.6L intercooler, pipe, size, routing
#24
SadFab CEO
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
Now that I think about it, some probably don't use it because the mixing mani and the front housing have nipples right there ready to go. No point in pulling a plug and ordering a fitting unless you are removing the front neck and or mixing mani like we have done.
I wanted a 90 degree fitting and couldn't find what I needed without stacking up like 3 fittings, so I made my own banjo fitting. I couldn't even find an M12 to 8mm banjo to barb, easily or cheaply anyway. I have some m12 banjo bolts from my Subaru that I found after I made my own bolt, and I can make you a banjo block fitting thing if you want.
https://www.miataturbo.net/build-thr...1/#post1251519
theres plenty of m12x1.25 to AN options though if you want to cobble that together somehow.
AN6 6AN JIC Flare to M12x1 25 Metric Straight Fuel Oil Fitting Adapter Blue | eBay
I wanted a 90 degree fitting and couldn't find what I needed without stacking up like 3 fittings, so I made my own banjo fitting. I couldn't even find an M12 to 8mm banjo to barb, easily or cheaply anyway. I have some m12 banjo bolts from my Subaru that I found after I made my own bolt, and I can make you a banjo block fitting thing if you want.
https://www.miataturbo.net/build-thr...1/#post1251519
theres plenty of m12x1.25 to AN options though if you want to cobble that together somehow.
AN6 6AN JIC Flare to M12x1 25 Metric Straight Fuel Oil Fitting Adapter Blue | eBay
#25
Now that I think about it, some probably don't use it because the mixing mani and the front housing have nipples right there ready to go. No point in pulling a plug and ordering a fitting unless you are removing the front neck and or mixing mani like we have done.
I wanted a 90 degree fitting and couldn't find what I needed without stacking up like 3 fittings, so I made my own banjo fitting. I couldn't even find an M12 to 8mm banjo to barb, easily or cheaply anyway. I have some m12 banjo bolts from my Subaru that I found after I made my own bolt, and I can make you a banjo block fitting thing if you want.
https://www.miataturbo.net/build-thr...1/#post1251519
theres plenty of m12x1.25 to AN options though if you want to cobble that together somehow.
AN6 6AN JIC Flare to M12x1 25 Metric Straight Fuel Oil Fitting Adapter Blue | eBay
I wanted a 90 degree fitting and couldn't find what I needed without stacking up like 3 fittings, so I made my own banjo fitting. I couldn't even find an M12 to 8mm banjo to barb, easily or cheaply anyway. I have some m12 banjo bolts from my Subaru that I found after I made my own bolt, and I can make you a banjo block fitting thing if you want.
https://www.miataturbo.net/build-thr...1/#post1251519
theres plenty of m12x1.25 to AN options though if you want to cobble that together somehow.
AN6 6AN JIC Flare to M12x1 25 Metric Straight Fuel Oil Fitting Adapter Blue | eBay
The Banjo bolt idea isn't bad, and I have thought about that too. I found a website that has the fitting in question and I ordered some. I kind of screwed up the order and got 8mm barb fittings which seem a bit small for my 3/8 ID slip fittings on my turbo. Not sure if that would cause a problem or not and the largest OD offered in the correct size is 10mm. I may just order these and try to recoup some of the cost by selling them to members on here for a few bucks shipped. Atleast until I break even with.
M12x1.25 to 10mm barb
#26
I'm planning on using that water port on my 1.6L as well. I just ordered both of these, let's hope they fit:
JEGS Performance Products 110071, JEGS AN Push-Loc Hose End Fittings | JEGS Performance Products
Earl's AT991945, Earl's Ano-Tuff Carburetor Fittings | Earl's
JEGS Performance Products 110071, JEGS AN Push-Loc Hose End Fittings | JEGS Performance Products
Earl's AT991945, Earl's Ano-Tuff Carburetor Fittings | Earl's
#30
Here's the 2.5" intercooler plumbing kit I bought:
Aucxracing intercooler plumbing kit
Here's my coldside plumbing mocked up (I call this "The Cobra"):
The Cobra!
- it connects my Fab9 350hp intercooler coldside to my Skunk2 TB.
So from the original plumbing kit I only used a J bend and a cut-down 90* bend. The couplers were of no use (probably could have used one of the straight ones) and I used better clamps.
Thread
Thread Starter
Forum
Replies
Last Post
Baxgordum
Miata parts for sale/trade
13
10-30-2015 07:42 AM
cyotani
Miata parts for sale/trade
9
10-26-2015 10:18 AM