Zabac

iTrader: (39)

keep dreaming...i do!!! LOL

sv650_ck

iTrader: (10)

Had to send the F/IC back to AEM to get looked at. Would run good if I held the harness just right. Otherwise, was experiencing signal dropout, rough running, cel, etc., whenever I moved the harness around. Runs fine with the bypass plug installed. The bypass plug pins look to be larger that those on the F/IC which I think may have caused the sockets in the harness connector to enlarge.

Didn't like the way the A-pillar pod blocked the view so went with a TDR gauge panel. Slotted the inner shift boot to route the O2 cable through.

cjernigan

iTrader: (13)

That's the TDR panel? That's the same thing i have, $20 shipped on ebay.

Stephanie Turner

How do you keep it from falling out?
Stephanie

sv650_ck

iTrader: (10)

but are they angled to the driver

Tabs on the back side secure it. Also used some rtv.

cjernigan

iTrader: (13)

Yep exact same thing. Guess they're making some major bank on those.
http://tinyurl.com/2mq5th
The trim panel that goes around it all hold it in well too.

gdnimr0d

iTrader: (16)

any updates on your ecu?

sv650_ck

iTrader: (10)

Won't make it AEM until ~30Nov.

Pitlab77

iTrader: (3)

its Dec....?

hustler

iTrader: (6)

i wish I had ceramic coating on my kit.

pschmidt

iTrader: (19)

Where did you pick up the sandwich plate in that pic?

cjernigan

iTrader: (13)

You can get one just like it on ebay. Or anplumbing.com sells them. Should be 20mm, pretty sure the civic uses the same thread. Glowshift sells them.

teknikscian

iTrader: (3)

20x1.5 is what you need for a sammmmich plate.

keep us updated on the AEM install, i just picked one of those up...

Stephanie Turner

How is the turbo install coming? Any new photos?
Stephanie

sv650_ck

iTrader: (10)

Haven't started yet. Patiently waiting to get my F/IC back from AEM - should be here this Thursday. Still trying to find out what if anything they did in the two weeks they had it. Regardless will be starting the install this weekend with pics to follow.

sv650_ck

iTrader: (10)

Just to follow up on the F/IC problems I'm having. AEM looked at the unit and couldn't find anything wrong with it and sent it back along with a new harness. Wired the new harness in and still having the same problem with the engine running rough/dieing when the unit is moved around. Runs fine with the bypass harness installed. Sent AEM some vids to show them.

http://s16.photobucket.com/albums/b3...ssHarnness.flv

http://s16.photobucket.com/albums/b3...CInstalled.flv

Trent

iTrader: (11)

those videos seem pretty conclusive to me.

emmi

did u cut of the spliced sections of the harness?? theres a possibility that they are contacting each other when moving. but its kinda hard to see in the video... im running the same set up as you (like scary identical) but on my 01. f/ic w/ uego and everything is wired up and it runs like stock. (havnt gotten to install the turbo yet)

sv650_ck

iTrader: (10)

Mine runs like stock with the bypass harness installed. Doesn't matter how much you shake, twist, etc., it doesn't miss a beat. I was hoping to have the fueling stuff working before installing the turbo but not gonna happen. May have to pick up a used voodoo card to get me going.

emmi

okay well i regretted doing this but the problem is in v2 which i recall u do having frm the video...

i just updated mine right now and my car got hella fucked up... im trying right now to downgrade back to V1 damn....

it idled, then it threw a CEL and it started bogging and drastically changing idle...