Intercooler pipes are through the hood...literally.
#22
duct tape this over your cuts:
Summit Racing Hood Scoop WRX 10" Long 25" Wide 2" Tall ABS Plastic Black Each | eBay
it will look better.
Summit Racing Hood Scoop WRX 10" Long 25" Wide 2" Tall ABS Plastic Black Each | eBay
it will look better.
#28
But the holes are already cut, right? I'll admit the thought process of "Hrm, my hood doesn't close tight because these pipes are in the way, brb getting my cutoff wheel" instead of "hrm, my hood doesn't close tight because these pipes are in the way maybe I should move them or get different pipes" isn't exactly the one I would have taken, but the fact remains it's too late for him to swap out pipes without either replacing the hood or patching the holes.. and if he's going to patch the holes he might as well patch them with patches that work with the pipes.
If it were me, I would go with the glassing/painting option found on the previous page.
Sand down to bare metal, wax paper, flanel or similar, glass over top, sand, body filler, sand, primer, sand, paint, sand, clear.
Unfortunately it's going to be approximately 37x more work than modifying the pipes, and probably just as much if not more money, but it's your best option at this point.
If it were me, I would go with the glassing/painting option found on the previous page.
Sand down to bare metal, wax paper, flanel or similar, glass over top, sand, body filler, sand, primer, sand, paint, sand, clear.
Unfortunately it's going to be approximately 37x more work than modifying the pipes, and probably just as much if not more money, but it's your best option at this point.
#29
But the holes are already cut, right? I'll admit the thought process of "Hrm, my hood doesn't close tight because these pipes are in the way, brb getting my cutoff wheel" instead of "hrm, my hood doesn't close tight because these pipes are in the way maybe I should move them or get different pipes" isn't exactly the one I would have taken, but the fact remains it's too late for him to swap out pipes without either replacing the hood or patching the holes.. and if he's going to patch the holes he might as well patch them with patches that work with the pipes.
If it were me, I would go with the glassing/painting option found on the previous page.
Sand down to bare metal, wax paper, flanel or similar, glass over top, sand, body filler, sand, primer, sand, paint, sand, clear.
Unfortunately it's going to be approximately 37x more work than modifying the pipes, and probably just as much if not more money, but it's your best option at this point.
If it were me, I would go with the glassing/painting option found on the previous page.
Sand down to bare metal, wax paper, flanel or similar, glass over top, sand, body filler, sand, primer, sand, paint, sand, clear.
Unfortunately it's going to be approximately 37x more work than modifying the pipes, and probably just as much if not more money, but it's your best option at this point.
Also, if I'm to cut the pipes, won't I be cutting off the bubble flares and losing part of my sealing surface? Will just the hose couplers seal against the flat surface of the pipes? Thanks for the response.
#33
Wanna come over? Another concern of cutting the pipes is having trouble with the angle. The Passenger side is basically a 90 from the dummy throttle body to the intercooler. If I cut length at the bottom, won't the angle to the intercooler be off when lowering pipe? Thanks for the response.
#37
I see much fail in your upper shroud cover. The radiator is lowered. And tilted. But that isn't the problem. The problem is the tubing that came with my kit. And again, The cuts were a temporary solution to get the car on the road. I never planned on leaving them like. I have another hood for the car. You could call it a fail if I did that and thought it looked cool and was going to keep it that way.
#39
I see much fail in your upper shroud cover. The radiator is lowered. And tilted. But that isn't the problem. The problem is the tubing that came with my kit. And again, The cuts were a temporary solution to get the car on the road. I never planned on leaving them like. I have another hood for the car. You could call it a fail if I did that and thought it looked cool and was going to keep it that way.
Just because the tubes that came with a kit are what came with the kit doesn't mean they're magically better than what other people can do with them. Just like the ebay universal kits, they are intentionally made to be cut and modified for your specific car.