need boost/vaccume line help fast
#1
need boost/vaccume line help fast
Could someone check this out real quick to make sure I wired all the lines correctly? Got a track day on sunday, and am getting it tuned tomorrow night, so just making sure everything is right before that.
The red line connects straight to the boost gauge, the yellow one goes to the BOV nipple.
Yellow line goes to the MAP
red is going to the turbo, yellow to the wastegate, and the blue is the controller/regulator.
Thanks guys
The red line connects straight to the boost gauge, the yellow one goes to the BOV nipple.
Yellow line goes to the MAP
red is going to the turbo, yellow to the wastegate, and the blue is the controller/regulator.
Thanks guys
#4
I'd recommend that you source the pressure line for your wastegate from somewhere after the IC and before the throttle. You will have pressure drop through the IC as flow increases. This will result in boost sag, even though you have a nice MBC. Joe Perez had a nice, easy to understand write-up on this.
#5
I'd recommend that you source the pressure line for your wastegate from somewhere after the IC and before the throttle. You will have pressure drop through the IC as flow increases. This will result in boost sag, even though you have a nice MBC. Joe Perez had a nice, easy to understand write-up on this.
I'm gonna look that up, thanks.
#7
Senior Member
iTrader: (3)
Join Date: Nov 2009
Location: Royal Palm Beach, FL
Posts: 725
Total Cats: 5
I'd recommend that you source the pressure line for your wastegate from somewhere after the IC and before the throttle. You will have pressure drop through the IC as flow increases. This will result in boost sag, even though you have a nice MBC. Joe Perez had a nice, easy to understand write-up on this.
you should not source boost from the compressor housing. you will get sag. red goes from housing to mbc?
#8
During cruise your turbo will be pushing 100% as the waste gate will be closed. It kinda defeats the throttle body as every time you're not at full boost the wastegate will be closed trying to get to the set boost however you're limiting the pressure going to the engine with the throttle body so you get a big mind ****. You press the gas, more exhaust goes to the turbo to spool it, turbo spools more but wastegate stays closed. You press the gas some more now you're in boost however still at low throttle so the turbo spools more as the wastegate still stays closed. You step to wot, the turbo has already spooled and built up a lot more than your set psi so you get a spike in psi so your wastegate now opens and you're fine. Now you're turning keeping the gas even, the throttle is say 30% open at 6psi however your wastegate is now closed so your turbo is trying to get to the set psi so it spools more so you close the throttle to make up for it, then when you step on the gas after the turn and you get another spike again throwing your rear end into the wall where you crash and burn and die. Is that what you want? This is why you cant have nice things!!1!
#11
Elite Member
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Sourcing bov boost from the compressor housing is at least better than manifold however sourcing boost between the IC and the TB is the best.
During cruise your turbo will be pushing 100% as the waste gate will be closed. It kinda defeats the throttle body as every time you're not at full boost the wastegate will be closed trying to get to the set boost however you're limiting the pressure going to the engine with the throttle body so you get a big mind ****. You press the gas, more exhaust goes to the turbo to spool it, turbo spools more but wastegate stays closed. You press the gas some more now you're in boost however still at low throttle so the turbo spools more as the wastegate still stays closed. You step to wot, the turbo has already spooled and built up a lot more than your set psi so you get a spike in psi so your wastegate now opens and you're fine. Now you're turning keeping the gas even, the throttle is say 30% open at 6psi however your wastegate is now closed so your turbo is trying to get to the set psi so it spools more so you close the throttle to make up for it, then when you step on the gas after the turn and you get another spike again throwing your rear end into the wall where you crash and burn and die. Is that what you want? This is why you cant have nice things!!1!
During cruise your turbo will be pushing 100% as the waste gate will be closed. It kinda defeats the throttle body as every time you're not at full boost the wastegate will be closed trying to get to the set boost however you're limiting the pressure going to the engine with the throttle body so you get a big mind ****. You press the gas, more exhaust goes to the turbo to spool it, turbo spools more but wastegate stays closed. You press the gas some more now you're in boost however still at low throttle so the turbo spools more as the wastegate still stays closed. You step to wot, the turbo has already spooled and built up a lot more than your set psi so you get a spike in psi so your wastegate now opens and you're fine. Now you're turning keeping the gas even, the throttle is say 30% open at 6psi however your wastegate is now closed so your turbo is trying to get to the set psi so it spools more so you close the throttle to make up for it, then when you step on the gas after the turn and you get another spike again throwing your rear end into the wall where you crash and burn and die. Is that what you want? This is why you cant have nice things!!1!
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM