1991 1.6 Greddy
#21
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Results with HR code
First, please understand that these new results are *not* load tuned. I pulled timing in higher boost back 5° and 3° back in mid boost across the table. Even though the results are lower, the car runs much better than before and does not feel any slower to me at all.
Here's how she pulled yesterday at the MS meet at DIY (same dyno as before). This is with the same setup I've been running for a while, spark fired through Toyo Cops, plugs at stock .045" gap.
236whp / 220wtq--waiting on DIY to email me the graphs
Can you say boost control issues?
Now, remember above when I said the car doesn't feel slower than before? Below is a cap from a pull on the street. Notice how much higher and sooner full spool is. Also note how much better it's held. I bet there's at least the 20 whp that can't be accounted for on the dyno. And this is with spark peeled back.
Here's how she pulled yesterday at the MS meet at DIY (same dyno as before). This is with the same setup I've been running for a while, spark fired through Toyo Cops, plugs at stock .045" gap.
236whp / 220wtq--waiting on DIY to email me the graphs
Can you say boost control issues?
Now, remember above when I said the car doesn't feel slower than before? Below is a cap from a pull on the street. Notice how much higher and sooner full spool is. Also note how much better it's held. I bet there's at least the 20 whp that can't be accounted for on the dyno. And this is with spark peeled back.
#23
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
No, unfortunaltey with the new code I'm running there's a hoop to jump through before I can log boost duty cycle. Which I just haven't done. But I have no reason to believe that it's anything other than what I've laid into the boost duty table posted.
#25
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
It's the load dyno. I don't think the ramp rate and run time used were correct. Which also explains why my MAP curve looks entirely different on the street than on the dyno.
I'm probably going to be running on a dynodynamics later this week, just for a comparison. I met the owner of a semi-local shop with one, and he said I could come and take pulls for free when I wanted.
I'm probably going to be running on a dynodynamics later this week, just for a comparison. I met the owner of a semi-local shop with one, and he said I could come and take pulls for free when I wanted.
#28
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Here's my plot from Saturday. Compare the tq curve to the falling boost curve.
Like with Atl93's run, the dyno wasn't set up right. I can't imagine how it's not putting down at least 260 with the way it drives.
Like with Atl93's run, the dyno wasn't set up right. I can't imagine how it's not putting down at least 260 with the way it drives.
#29
Supporting Vendor
iTrader: (3)
Join Date: Jul 2006
Location: San Diego
Posts: 3,303
Total Cats: 1,216
If we asked the EBC to hold boost at 15 psi, what would happen? Well, if I had a built motor I could carry more boost to redline and keep the torque curve very flat to redline. The HP curve would contiune on its steep increasing slope, though we're really starting to push the compressor, but there may be 270 rwhp in there.
Thanks I just like to keep learning.
-Ryan
#31
If I may ask for some clarification here, if your motor is able to handle the 15 psi that it shows you climb to, why would you need a built motor in order to handle holding that 15 psi to redline? Is a given pressure harder on the motor the higher the rpms?
Thanks I just like to keep learning.
-Ryan
Thanks I just like to keep learning.
-Ryan
Thread
Thread Starter
Forum
Replies
Last Post
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM
russian
Miata parts for sale/trade
6
10-08-2015 03:01 PM