ThePass

iTrader: (3)

Looks like a fun bike and it's getting well used now. I just took a Supermoto riding school recently and it's stupid fun. ridiculous lean angles on asphalt then transition to dirt, take a couple jumps, rear of the bike squirming all over the place, back to asphalt and looking for grip with dirty tires.. was a real hoot. I could see getting into that.

Oh and thanks for the brass vice jaw cap suggestion guys, I'll probably make something like that

-Ryan

ThePass

iTrader: (3)

Question for those who are familiar with AC TIG welding..
I took some classes and have been practicing TIG, just switched from steel to aluminum today, and now that I'm welding on AC I keep getting a small zap/shock through the table into my arm/hand - whatever is touching the table - right when I light the arc up. I'm wearing a long sleeve cotton shirt. Googling a bit turned up suggestions to ground the table to something but it's not my shop/space so DIY solutions aren't so much an option. Am I doing something wrong or is this common?
It doesn't seem to happen through the leather gloves, so I'm thinking leather sleeves could solve the issue for me..

-Ryan

Erat

iTrader: (5)

Yes. It's common. For me anyways, i've always gotten it.

Solution is to wear some gloves / better insulate yourself from the table.

Leafy

iTrader: (1)

I try not to touch the table/work piece with my off hand until the arc is started and its time to add filler. But I normally only get zapped when I arc tungsten to filler (oops), or if the ground is shitty.

TurboTim

iTrader: (9)

Try welding in the summer, in a 90+ °F garage. That'll help.

Remember, you can't have a fan blowing on you because that'll blow away the argon.

The zaps sometimes noticeably change my mood. Like...for a few minutes I think the world is going to end.

Welding AC current triggers my front lawn sprinklers. I have to unplug my timer box whenever I weld aluminum at home.

ThePass

iTrader: (3)

Hahaha wish there was a "like" button for posts, this would get it
Thanks for the input guys, It's only beeen a nuissance nothing more, I was just concerned I may be doing something wrong and not knowing it.

Going back today to weld up all the changes to my intercooler. Nervous yet excited.

-Ryan

Leafy

iTrader: (1)

Pre heat that bastard. I wish I did mine. The 2nd half of the weld on mine when it was already super hot looks way better than the first half when it was cold.

krazykarl

I have to unplug my coffee grinder for the same reason. First time messing with aluminum, the next morning I found that it had ground all the beans that I had in there.

hornetball

iTrader: (4)

Give a prop then.

ThePass

iTrader: (3)

Oh is that what that props thing is? I'm a hahaha

shuiend

iTrader: (24)

Mazdaspeed3 motor in a lotus7 clone. I think the counts as some custom fabrication. Corky has been working on it for a while.

Full_Tilt_Boogie

iTrader: (1)

Why is the BOV like that?

bikersam717

iTrader: (5)

Because race car.

thenuge26

iTrader: (2)

I assume also because tiny engine bay.

Full_Tilt_Boogie

iTrader: (1)

Im going to route my BOV into the interior of the car so it blows off in my face like a turbocharged cumshot.

samnavy

iTrader: (7)

You just made my week.

thenuge26

iTrader: (2)

Route EWG dump into anus and BOV into mouth, DP win.

carbon

iTrader: (1)

When that oil seal blows be prepared for HIV incoming.

shuiend

iTrader: (24)

It was a fitment issue. Tiny engine bay in 7 replicas, so you dit things where you can.

mad city miata

iTrader: (1)

This is the best!