Diff mounts?
#23
Elite Member
iTrader: (5)
Join Date: Jul 2006
Location: Central California
Posts: 2,544
Total Cats: 4
i really doubt it will make it go away completely, and i hope i am proven wrong.
#25
i put the diff mounts in approx 6 months ago and only noticed slight increase in vibrations, As far as wheel hop, never really had any problems-before or after. I just put the mmr motor mounts in this past week and the whole package is pretty rediclus as Brainack....
my MSM motor mounts are fs in the fs section...
my MSM motor mounts are fs in the fs section...
#30
Elite Member
iTrader: (5)
Join Date: Jul 2006
Location: Central California
Posts: 2,544
Total Cats: 4
Well I installed the MMRs, but i gotta pull my rear out to rebuild because theres too much gear-lash. In the two days I was running them, it made engagement very crisp. There was some additional droning between 3500 and 5500rpm, but not too bad, especially considering that my 3" exhaust is not too quiet.
#31
http://www.iscracing.net/
These are the diff mounts I have (scroll down on the right side). They were machined perfectly to fit and the rear end feels much "crisper" now. Not sure that's the right word for it, but it's sunday morning and i'm still half asleep.
Now if I can find the time to do the engine mounts we'll be in good shape....my engine mounts are completely shot.
These are the diff mounts I have (scroll down on the right side). They were machined perfectly to fit and the rear end feels much "crisper" now. Not sure that's the right word for it, but it's sunday morning and i'm still half asleep.
Now if I can find the time to do the engine mounts we'll be in good shape....my engine mounts are completely shot.
#33
Elite Member
iTrader: (15)
Join Date: Sep 2007
Location: Incline Village, NV
Posts: 2,034
Total Cats: 5
Remove old mounts, Put new MMR mounts in.
Ive herd removing the old mounts can be a bitch, Ive herd of torching them, drilling holes in them, using a dremmel with a chisel tool. Reguardless they need to come out, once out the mmr mounts will just drop into place.
Ive been driving on MMR mounts for about 2 months now, Love them.
Ive herd removing the old mounts can be a bitch, Ive herd of torching them, drilling holes in them, using a dremmel with a chisel tool. Reguardless they need to come out, once out the mmr mounts will just drop into place.
Ive been driving on MMR mounts for about 2 months now, Love them.
#34
MMR isn't publicly selling mounts it seems anymore. You can get the same mount here though: http://www.driftingjellyfish.com/
#35
http://iscracing.net/Miata_Brake_Diff.htm
I have the MMR mounts with a rigid clutch disc. Vibrates like a cheap motel bed. The Super Pro's are a lot more expensive but should be somewhere in between the Mazda 40% and the Delrins. Haven't tested them yet.
I have the MMR mounts with a rigid clutch disc. Vibrates like a cheap motel bed. The Super Pro's are a lot more expensive but should be somewhere in between the Mazda 40% and the Delrins. Haven't tested them yet.
#36
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
http://www.driftingjellyfish.com/
I have those sitting on my desk waiting to go in. they are my new pen holder for the time being.
I have those sitting on my desk waiting to go in. they are my new pen holder for the time being.
#39
Senior Member
iTrader: (2)
Join Date: May 2005
Location: Edmonton Ab, Canada
Posts: 1,202
Total Cats: 21
Well I just found some delrin and uhmw hpde on ebay for el-cheapo (cost prolly 20bux for a set made of delrin) and can machine them at work for free, need some dimensons then I could make a few extra sets if anyone wants them, cost plus shipping would suffice. Intrest??