my xtd is a peice of shit
#1
Senior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2005
Location: South Carolina
Posts: 582
Total Cats: 0
my xtd is a peice of **** *carnage added*
i hate this ******* thing what a ******* waste. first it has an issue with not disengauging fully. ran out of adjustment on the pedal so i was stuck with having my engagment point about 1/2 inch off the floor. that made me pissed. then throw out bearing started making noise. now on day 7 the throw out bearing is shot probly seized and that means my presure plate forks are probly fucked to hell now and the damn thing only has about 170 miles on it. never got it to even go in gear smooth cause the clutch never disengaged enough. i am running a brand new cmc and slave. looks like i gotta take the tranny BACK out and see wtf.
act ... i didnt want to, but it looks like i may have to let you rape my wallet.
act ... i didnt want to, but it looks like i may have to let you rape my wallet.
Last edited by mxv; 02-26-2007 at 10:07 PM.
#11
Senior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2005
Location: South Carolina
Posts: 582
Total Cats: 0
yea, mine sucks but i am sure there are guys that have good luck. i read enough good posts about them to give them a try looks like i may have a dud. but once again i wont know till i take it out. if i can still use my disk whats a good presure plate for 220 wtq holding capacity that wont cost much? i have a feeling that the xtd's got eaten up by the seized up throw out bearing.
#12
yeah, spend almost as much on a spec and risk doing it all over again. get a ******* ACT XT and be done with it. I don't know why so many on this forum try to save a few bucks on one of the most important parts of the car and the biggest bitch to replace.
A good quality $330 277tq clutch is NOT expensive.
A good quality $330 277tq clutch is NOT expensive.
#13
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
yeah, spend almost as much on a spec and risk doing it all over again. get a ******* ACT XT and be done with it. I don't know why so many on this forum try to save a few bucks on one of the most important parts of the car and the biggest bitch to replace.
A good quality $330 277tq clutch is NOT expensive.
A good quality $330 277tq clutch is NOT expensive.
#15
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
My buddies car and the TDR car both sit on the floor. I'm going to take a risk either way, one might fail, one might be such a pain in the *** to drive that its not worth the additional $100.
#16
Senior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2005
Location: South Carolina
Posts: 582
Total Cats: 0
well the position is so low it never disengages all the way. so when i put in first it goes clanggg. and then 2nd 3rd and 4th and 5th go crunch... just because of this i will not beable to compete at all. everything needs to work. no matter how cheap it is if i pay money for somthing it just has to work... sorry.
is the pressure plate what decides your pedal height? if so... what is one that can hold 220tq and 220 hp and has height that is normal with what ever pedal presure, i could care less.
is the pressure plate what decides your pedal height? if so... what is one that can hold 220tq and 220 hp and has height that is normal with what ever pedal presure, i could care less.
#17
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
well the position is so low it never disengages all the way. so when i put in first it goes clanggg. and then 2nd 3rd and 4th and 5th go crunch... just because of this i will not beable to compete at all. everything needs to work. no matter how cheap it is if i pay money for somthing it just has to work... sorry.
is the pressure plate what decides your pedal height? if so... what is one that can hold 220tq and 220 hp and has height that is normal with what ever pedal presure, i could care less.
is the pressure plate what decides your pedal height? if so... what is one that can hold 220tq and 220 hp and has height that is normal with what ever pedal presure, i could care less.