R&D thread for shim-under-bucket conversion!
#43
Basically if you make a single spring a lot stiffer than stock, the wire will see too much stress, and a dual spring setup will be a better engineering solution; and then the dual setup is designed for the springs to have a different resonant frequency so that the result is a pair of small resonances instead of a single big one. This resonance can cause a "travelling wave" to move up and down the spring and cause the valve to bounce off the seat after closing. A bigger problem with boost behind the intake valves, which will need a higher valve-closed pressure (force, really). This is what manifests as "valve float" and loss of power at high RPM.
I first checked if I could use just the outer spring for my M3 and it turns out they're softer than the cone shaped stockers. I don't know if this applies to the miata because the miata has standard cylindrical springs. Cone shaped springs allow thicker wire (stiffer) with shorter coil-bind-length. So I had to buy the whole shebang. ($$$, esp. with 50% more cylinders than a miata) The little ******* were more than half the price of my cam regrind.
In order to engineer dual springs you have to use their retainers. In order to sit both springs on the head properly you need their lower spring seat.
The springs primarily need to be stiff enough to decelerate the valves which peaks at the cam's nose. Deceleration is proportional to RPM squared, just like rod stress (not exponential ). So spring open pressure (force, really), needs to stiffen proportionally to RPM squared, but inversely proportional to valvetrain mass (valve+follower+shim+retainer+keepers+1/3rd spring). If the springs are too soft, the lifter can "take off" like a ski jumper and cause rapid wear on the cam and lifter due to the "harsh landing".
Because the valve deceleration profile is a function of the cam profile and RPM, the spring stiffness should be specified by the cam designer. Ironically more lift can allow for a less aggressive deceleration profile despite a more aggressive opening ramp; but many factory springs run very close to coil bind, to prevent dropping a shim during a mis-shift. The bind prevents the valve opening too far and a gap under the lobe forming big enough to drop a shim. This may be why miatas don't seem to drop stock shims during a mis-shift, unlike say, a Sentra. More duration also allows for a less aggressive opening ramp. However, an aggressive opening ramp with a high peak velocity allows for more "area under the curve" and makes for more airflow for a given 0.050" duration - too much duration screws up low end torque.
#46
Elite Member
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
Bumping the worlds oldest thread.
Did anyone ever use a micrometer to determine the OD and depth of the factory HLA?
I have a set of skyline GTR lifters in my room...(from the list) and I am interested in running them if they fit...
Did anyone ever use a micrometer to determine the OD and depth of the factory HLA?
I have a set of skyline GTR lifters in my room...(from the list) and I am interested in running them if they fit...
#47
another big bump from me....you know I don ´t like to do new threads if there is no need to.
My question is simple. What is the right way to measure the thickness of the shim under bucket ?
I have custom grind cams with 33mm base circle. Is it ok to just install my valves, springs, retainers, then put on it mazdacomp bucket lifter (shim under bucket type) and measure cold lash between cam and the lifter surface, and from there determine the needed shim size ?
or do I need to use stock BP4W buckets with shims over lifter, measure each shim, put it in the head and measure the cold lash,, then to what I will measure add shim thickness, and somehow work out the thickness for shim under bucket shim ?
I think the first method should work if the lifter will not end up hitting something. But as this is my first shim under bucket lifter swap I don´t know how to.
Thanks for you help !
My question is simple. What is the right way to measure the thickness of the shim under bucket ?
I have custom grind cams with 33mm base circle. Is it ok to just install my valves, springs, retainers, then put on it mazdacomp bucket lifter (shim under bucket type) and measure cold lash between cam and the lifter surface, and from there determine the needed shim size ?
or do I need to use stock BP4W buckets with shims over lifter, measure each shim, put it in the head and measure the cold lash,, then to what I will measure add shim thickness, and somehow work out the thickness for shim under bucket shim ?
I think the first method should work if the lifter will not end up hitting something. But as this is my first shim under bucket lifter swap I don´t know how to.
Thanks for you help !
#49
that is what I wanted to hear ! thank you
Also is there a difference between mazdacomp and supermiata buckets ? I´ve read somewhere that 949 have them made by supertech, but they seem to be very cheap compared to supertech ones, which are sold by other vendors. on the other hand they seem to be the price range of the mazdacomp ones.
Also is there a difference between mazdacomp and supermiata buckets ? I´ve read somewhere that 949 have them made by supertech, but they seem to be very cheap compared to supertech ones, which are sold by other vendors. on the other hand they seem to be the price range of the mazdacomp ones.
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM