Notices
Insert BS here A place to discuss anything you want

Aw Fuckin' A

Old May 11, 2007 | 12:52 PM
  #1  
Braineack's Avatar
Thread Starter
Boost Czar
iTrader: (62)
 
Joined: May 2005
Posts: 80,552
Total Cats: 4,368
From: Chantilly, VA
Default Aw ******' A

it wasnt just my sensor that crapped out, the LC-1 is not working properly....

no sensor plugged in and get "voltage too low error 9"

plugged matt's sensor in and get "heater circuit open error 2"

same thing on my sensor....

retraced the wiring, nothing has changed, just crapped out on me.

So, tomorrow is the dyno and now I gotta rely on the crap "sniffer" for a wbo2 plot....oh well, it's tuned close where i dont need one, but I was in the middle of fine tuning cruise when it died, I'll propably have crap for fuel mileage on the way....

that DIY WB guy is looking a lot better to me right now.
Old May 11, 2007 | 12:54 PM
  #2  
Ben's Avatar
Ben
Supporting Vendor
iTrader: (33)
 
Joined: Jul 2006
Posts: 12,659
Total Cats: 134
From: atlanta-ish
Default

That really sucks man. Call Innovate and speak with Phillipe. Maybe he'll offer a RMA on it and bench test it.
__________________
Chief of Floor Sweeping, DIYAutoTune.com & AMP EFI
Crew Chief, Car Owner & Least Valuable Driver, HongNorrthRacing

91 Turbo | 10AE Turbo | 01 Track Rat | #323 Mazda Champcar

Originally Posted by concealer404
Buy an MSPNP Pro, you'll feel better.
Old May 11, 2007 | 01:11 PM
  #3  
y8s's Avatar
y8s
DEI liberal femininity
iTrader: (8)
 
Joined: Jun 2005
Posts: 19,338
Total Cats: 574
From: Fake Virginia
Default

isn't someone bringing a brand new LC1 setup? plug and play baby
Old May 11, 2007 | 01:16 PM
  #4  
TurboTim's Avatar
Elite Member
iTrader: (9)
 
Joined: Jun 2006
Posts: 7,035
Total Cats: 425
From: Chesterfield, NJ
Default

Damn. If you had known earlier, I could have picked up my LC1 box at the store this morning when I picked up my helmets. Sorry :(
Old May 11, 2007 | 01:18 PM
  #5  
Al Hounos's Avatar
Senior Member
 
Joined: Oct 2005
Posts: 1,168
Total Cats: 0
From: Knoxville
Default

What does DIY autotune think about putting a resistor on the LC1 analog out like the innovate guys say to? How has it been dealt with on the PnP?
Old May 11, 2007 | 01:21 PM
  #6  
Braineack's Avatar
Thread Starter
Boost Czar
iTrader: (62)
 
Joined: May 2005
Posts: 80,552
Total Cats: 4,368
From: Chantilly, VA
Default

Originally Posted by TurboTim
Damn. If you had known earlier, I could have picked up my LC1 box at the store this morning when I picked up my helmets. Sorry :(

go back :(
Old May 11, 2007 | 01:28 PM
  #7  
Splitime's Avatar
Miotta FTW!
iTrader: (24)
 
Joined: Jun 2006
Posts: 4,290
Total Cats: 31
From: Chicagoland, IL
Default

Call Innovate at least, they warrantied my LM1 awhile back and I was the second owner. Very easy people to deal with.
Old May 11, 2007 | 01:32 PM
  #8  
Braineack's Avatar
Thread Starter
Boost Czar
iTrader: (62)
 
Joined: May 2005
Posts: 80,552
Total Cats: 4,368
From: Chantilly, VA
Default

Yeah, actually PMed Jerry from DIY since I bought it through them...ill play with it later and try again, but then I'll get in touch with Philippe at Innovative.

I might rip it out completely and try to temporarily rewire it, as I routed it all donkey. But it was wokring and then not, and another sensor throws the same errors, so i dont have my hopes set too high.
Old May 11, 2007 | 01:55 PM
  #9  
samnavy's Avatar
Elite Member
iTrader: (7)
 
Joined: Apr 2006
Posts: 6,463
Total Cats: 327
From: VaBch, VA
Default

I'll be bringing my brand new, still in plastic LC-1 to NEDD... you're welcome to give it a shot!
Old May 11, 2007 | 02:05 PM
  #10  
Braineack's Avatar
Thread Starter
Boost Czar
iTrader: (62)
 
Joined: May 2005
Posts: 80,552
Total Cats: 4,368
From: Chantilly, VA
Default

I could at least try to wire it up and see if i get the same error, but i doubt I'll get around to it tomorrow during the course of the day...its only a few wires, but i really dont know if wanna bother crawling under the car and pulling ****..we'll see....

ill be fine on the dyno without one, just sucks that i wont be able to capture my logs with the wbo2 reading...and i really cant tune anything, so im stuck with my map as is....but i do need a fix sometime soon...if its not one thing it's always another.
Old May 11, 2007 | 04:00 PM
  #11  
that7guy's Avatar
Junior Member
iTrader: (1)
 
Joined: Apr 2005
Posts: 430
Total Cats: 9
From: Bethesda, MD
Default

Dude that sucks!
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
calteg
Miata parts for sale/trade
21
Oct 27, 2014 08:25 PM
Quality Control Bot
Insert BS here
27
Oct 6, 2011 09:41 AM
Pen2_the_penguin
Insert BS here
12
May 3, 2010 07:22 PM
johndoe
Insert BS here
8
Sep 2, 2008 12:48 PM
miataz
Insert BS here
22
Jan 4, 2008 12:00 PM


Thread Tools
Search this Thread

All times are GMT -4. The time now is 08:15 AM.