Totally unrelated fab project
#1
Elite Member
Thread Starter
iTrader: (46)
Join Date: Dec 2007
Location: Nebraska
Posts: 4,729
Total Cats: 166
Totally unrelated fab project
I built this little articulating 4WD loader a few years ago. It usually wears a 48" bucket for general dirt moving, cleaning out the horse barn, etc.
I cut a lot of firewood. We have a wood stove in the basement and I heat my shop with wood. (It was close to 0* last night with a 45 mph wind, but the shop was 74*
Anyway, I got tired of lugging wood to the truck when cutting firewood, so I built this grapple for my loader. Now I can cut 8' lengths, pick them up and load them into the trailer. When the front half of the trailer is full, I drive the loader back on and go home. Use the loader to unload the wood at the splitter and cut into firewood chunks right at the splitter.
It has handled as big of a piece as I have cut so far. Lifting capacity is supposed to be 500 lbs, but that is with a 200 lb bucket on it, so it will handle a pretty good chunk of wood.
I cut a lot of firewood. We have a wood stove in the basement and I heat my shop with wood. (It was close to 0* last night with a 45 mph wind, but the shop was 74*
Anyway, I got tired of lugging wood to the truck when cutting firewood, so I built this grapple for my loader. Now I can cut 8' lengths, pick them up and load them into the trailer. When the front half of the trailer is full, I drive the loader back on and go home. Use the loader to unload the wood at the splitter and cut into firewood chunks right at the splitter.
It has handled as big of a piece as I have cut so far. Lifting capacity is supposed to be 500 lbs, but that is with a 200 lb bucket on it, so it will handle a pretty good chunk of wood.
#3
Elite Member
Thread Starter
iTrader: (46)
Join Date: Dec 2007
Location: Nebraska
Posts: 4,729
Total Cats: 166
It is similar to a skidsteer loader. Four independent hydraulic wheel drive motors run in series on each side to provide a LSD. All driven by a single hydraulic pump with a rotary flow divider to split the flow. Steering is by a hydraulic cylinder that bends the machine at the articulating joint in the center. It can be seen in the "turning" configuration in the second pic. I didn't design it. I built it from plans so I can't take credit for the design or drive mechanism.
#4
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,660
Total Cats: 3,011
Very nice!
I never thought about having one that small and inexpensive. Hydrostatic drive is the way to go on machines that size.
You could probably build them and make money on them if it's not to big a pain to do.
Mom and pop landscape shops and people with a couple of acres could probably see the value in one.
I sell these for a living - Kawasaki Construction Machinery Corp. of America — ZV-2 Wheel Loaders
I never thought about having one that small and inexpensive. Hydrostatic drive is the way to go on machines that size.
You could probably build them and make money on them if it's not to big a pain to do.
Mom and pop landscape shops and people with a couple of acres could probably see the value in one.
I sell these for a living - Kawasaki Construction Machinery Corp. of America — ZV-2 Wheel Loaders
#6
Elite Member
Thread Starter
iTrader: (46)
Join Date: Dec 2007
Location: Nebraska
Posts: 4,729
Total Cats: 166
Yeah, those were about $300 each then, now $400 each. I have right at $7K in it with all new parts including the 18 hp briggs, pump, valves, steel. Depends on what you call inexpensive. When I see acreage owners spending $9K on ZTR mowers and $20-30K acreage tractors, it probably is inexpensive.
#7
Elite Member
Thread Starter
iTrader: (46)
Join Date: Dec 2007
Location: Nebraska
Posts: 4,729
Total Cats: 166
Very nice!
I never thought about having one that small and inexpensive. Hydrostatic drive is the way to go on machines that size.
You could probably build them and make money on them if it's not to big a pain to do.
Mom and pop landscape shops and people with a couple of acres could probably see the value in one.
I sell these for a living - Kawasaki Construction Machinery Corp. of America — ZV-2 Wheel Loaders
I never thought about having one that small and inexpensive. Hydrostatic drive is the way to go on machines that size.
You could probably build them and make money on them if it's not to big a pain to do.
Mom and pop landscape shops and people with a couple of acres could probably see the value in one.
I sell these for a living - Kawasaki Construction Machinery Corp. of America — ZV-2 Wheel Loaders
Thread
Thread Starter
Forum
Replies
Last Post
Greasyman
General Miata Chat
2
09-28-2015 10:44 AM