Help me start my diypnp
#1
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
Help me start my diypnp
Hey guys, I just came in from trying to start my diypnp on my 95 miata with sequential injection. I couldn't get it to start, only stutter. I found two problems that i have, and i don't know if they're related to my tunerstudio tune or my wiring.
Two problems are:
1. AEM UEGO isn't connecting to laptop/ecu. I have the white wire from the aem wired into pin 1 of my db15 connector, and I believe that is connected to the 02 inside my box.
2. Bigger problem: Only cylinder 1 and three are getting gas. 1 and 3 plugs are wet, 2 and 4 are dry. I am running sequential injection with id1000 injectors. Req fuel set at 3.1 according to calculator with 1839 cc 4 cylinders 1000 cc injectors
What I Know:
All four cylinders are getting spark
I have the sequential injection chip set up inside, so maybe im missing a setting for that somewhere.
I am posting up my msq. and will post my excel jumper spreadsheet in a sec.
Thanks for all the help bros.
Two problems are:
1. AEM UEGO isn't connecting to laptop/ecu. I have the white wire from the aem wired into pin 1 of my db15 connector, and I believe that is connected to the 02 inside my box.
2. Bigger problem: Only cylinder 1 and three are getting gas. 1 and 3 plugs are wet, 2 and 4 are dry. I am running sequential injection with id1000 injectors. Req fuel set at 3.1 according to calculator with 1839 cc 4 cylinders 1000 cc injectors
What I Know:
All four cylinders are getting spark
I have the sequential injection chip set up inside, so maybe im missing a setting for that somewhere.
I am posting up my msq. and will post my excel jumper spreadsheet in a sec.
Thanks for all the help bros.
#2
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
Okay here is my jumper set up spreadsheet. I also changed all my iginition settings to the settings on this page, didn't help at all.
As a side note, where do i go to set the timing to make sure it's at 10, like i had to do with the mspnp? Or do i not need that step with ms2?
As a side note, where do i go to set the timing to make sure it's at 10, like i had to do with the mspnp? Or do i not need that step with ms2?
#4
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
I think i only would have needed that for low impedance injectors.
Going to sleep now, waking up early tomorrow to start messing with it before school, hopefully someone wants to help me!! I think it is a simple problem that i'm overlooking.
Going to sleep now, waking up early tomorrow to start messing with it before school, hopefully someone wants to help me!! I think it is a simple problem that i'm overlooking.
#7
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
to bearda:
I do have a wire for each injector, i know its hard to tell from my excel but
inj1-4u
inj2-4y
inj3-4z
inj4-4v
#12
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
I just tried to re-download the msq, and i found a problem. It says it cant find the controller definition file for signature: MS2ExtraRel 3.0.3h. The ecu definition on my tune is MS2Extra Serial310. I couldnt find out where to download the specific 3.0.3h firmware before.
#14
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
Its not letting me open the file. This is when im trying to open it in tunerstudio. Ive tried opening into its own temp file as well as a previously saved file. The window says "Can not find the controller definition file (ini,ecu) for Signature:MS2Extra Rel 3.0.3h
Please select the appropriate configuration file"
Thanks for helping me brain and sorry if im doing stupid things.
Please select the appropriate configuration file"
Thanks for helping me brain and sorry if im doing stupid things.
#15
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
how are you opening the file?
typically, when I have a project open, and I'm opening a msq it was say the file you are loading doesn't match your project's firmware, yada yada do you want to convert? click okay.
sounds like you are opening this through windows, and letting it open in a temp project, but you dont have the firmware installed locally.
anyways: http://msextra.com/doc/ms2extra/files/alpha/
should be the ms2extra_alpha20090912.zip one
typically, when I have a project open, and I'm opening a msq it was say the file you are loading doesn't match your project's firmware, yada yada do you want to convert? click okay.
sounds like you are opening this through windows, and letting it open in a temp project, but you dont have the firmware installed locally.
anyways: http://msextra.com/doc/ms2extra/files/alpha/
should be the ms2extra_alpha20090912.zip one
#16
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
SWEET!!!
Okay so now i have the correct startup map loaded into tunerstudio, using that ecu definition you just told me. Now i have to reload the correct firmware form that file onto the ecu, using "download-MS2-firmware.bat" correct?
Thanks brain youre a boss
Okay so now i have the correct startup map loaded into tunerstudio, using that ecu definition you just told me. Now i have to reload the correct firmware form that file onto the ecu, using "download-MS2-firmware.bat" correct?
Thanks brain youre a boss
#17
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
I'd still want at least the latest release loaded on my MS, which is 3.1.1: http://msextra.com/doc/ms2extra/files/release/
But really I'd load 3.1.3 personally.
Regardless, you shouldn't have to reflash the MS to load the map, you just need the fimware locally so it knows what to do with it.
But really I'd load 3.1.3 personally.
Regardless, you shouldn't have to reflash the MS to load the map, you just need the fimware locally so it knows what to do with it.
#18
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
Thanks brain, i think i got everything figured out and reloaded, drop down menu is now available. Ill post back in here after i try to start it again.
Let me know if you ever need anything welded, you have helped me a lot on getting this setup.
Let me know if you ever need anything welded, you have helped me a lot on getting this setup.
#20
Senior Member
Thread Starter
iTrader: (6)
Join Date: May 2009
Location: San Francisco
Posts: 983
Total Cats: 23
It started!!! Got it started using the gas pedal, need to add some fuel but im late to school now because the miata is the main rioroty this morning!
SO PUMPED!!! LETS GET THIS EFR SPOOLIN!
SO PUMPED!!! LETS GET THIS EFR SPOOLIN!