Please Help Fast Ms Install Today!!!
#1
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
Please Help Fast Ms Install Today!!!
I Need Help On The Install I Got It All Wired Up I Think But When I Turn The Ignition On It Sounds Like Somethings Arcing By The Fuse Box???? Theres Nothing Hooked Up To That And I Cant Get My Laptop To See The Com Port On Get It To Connect To Ms????? Stuck At My Parents House Til I Get It To Run Just Hope I Didnt Fry Something? Followed All The Directions!!
#2
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,504
Total Cats: 4,079
first thing you need to do is get the laptop to connect before trying to crank. however it should start right up as i flashed it with a msq that should be close to what you need.
when you cranked it what happened? i dont understand this sound you are tlaking about....did it just crank and nothing happened?
did you install the fuel pump wire?
help me help you.
when you cranked it what happened? i dont understand this sound you are tlaking about....did it just crank and nothing happened?
did you install the fuel pump wire?
help me help you.
#3
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
okay first off i never cranked it i was to scared off the crackling/shorting out sound and i couldnt get the laptop to connect and i didnt know what maf wire to tap the mainly green with red line or red wire with green line? so i just put it back to the factory ecu for now and it starts up just fine but still makes sound when turn the ignition on? dont see sparks and it stops after a sec or 2?
#6
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,504
Total Cats: 4,079
go through my how-to sticky again. i copied and added to the instructions i sent you.
you need to get the laptop working...do you know what com port your serial cable is on? you must go to communication>settings and make sure it matches. it must also be on 1-4 com ports only.
once you confirm both, turn the ignition to ON, the PC should make a cool noise and your guages should light up. verify everything looks good. 0RPM, 97-101kPa, clt and ait temp looks ambient, etc.
before you crank make sure you changed all the settings i suggested in the configurator.
make sure you install both the AIT sensor and fuel pump wire or else it wont run.
once all that is done try cranking it.
also verify the solenoid is wired corrected, remove it altogether for the moment, mine doesnt make noise, but others say it clicks on startup.
you need to get the laptop working...do you know what com port your serial cable is on? you must go to communication>settings and make sure it matches. it must also be on 1-4 com ports only.
once you confirm both, turn the ignition to ON, the PC should make a cool noise and your guages should light up. verify everything looks good. 0RPM, 97-101kPa, clt and ait temp looks ambient, etc.
before you crank make sure you changed all the settings i suggested in the configurator.
make sure you install both the AIT sensor and fuel pump wire or else it wont run.
once all that is done try cranking it.
also verify the solenoid is wired corrected, remove it altogether for the moment, mine doesnt make noise, but others say it clicks on startup.
#7
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
i followed your directions exactly up until i plugged in the serial cable and tested the connection for ports 1-4 and it said no response with the key on
the serial cable i have now is a 15 pin cable that has a monitor symbol on the back, when i go to the device list the only com port is the printer so do i need to get a serial adapter to fit the printer or a usb adapter?
now that i put it back to the factory ecu and plugged everything exactly how it was, it starts but will not keep running, so i either need to fix that or hook megasquirt up because the car is stuck at my parents house
in the instructions you sent me you said to install the software for the serial cable...where do i get that because mine doesnt register any communication port other than the printer???
All the help you can offer will be much appreciated because i kind of need my car to run!!
the serial cable i have now is a 15 pin cable that has a monitor symbol on the back, when i go to the device list the only com port is the printer so do i need to get a serial adapter to fit the printer or a usb adapter?
now that i put it back to the factory ecu and plugged everything exactly how it was, it starts but will not keep running, so i either need to fix that or hook megasquirt up because the car is stuck at my parents house
in the instructions you sent me you said to install the software for the serial cable...where do i get that because mine doesnt register any communication port other than the printer???
All the help you can offer will be much appreciated because i kind of need my car to run!!