Notices
MEGAsquirt A place to collectively sort out this megasquirt gizmo

high map reading at idle, very slight IAC noise

Old Jul 29, 2008 | 03:01 PM
  #1  
N3v's Avatar
N3v
Thread Starter
Junior Member
 
Joined: May 2008
Posts: 314
Total Cats: 1
From: Nashville/Knoxville, TN
Default high map reading at idle, very slight IAC noise

To make this post much easier to understand, this is my current setup:
Name:  1-1.jpg
Views: 247
Size:  82.3 KB
I'm idling at about 60kpa and I'm pretty sure my IAC is to blame. On my setup, my IAC is over on the left side, what all those red silicone tubes are connecting to. If i squeeze the vaccuum line thats going straight to the IAC (the IAC is connected to a special 'block' that simply distributes the idling air to all four cylinders via the four red silicone tubes) the MAP gauge slowly climbs.

It might be a leak also, I'm looking into that.

Another thing is that my IAC's air intake port is just connected to a little filter directly next to it, and I can't hear anything standing over my engine bay, but if i put my ear up to this intake filter, i can hear a tone. Is that normal? Also, my itbs are set to be very very slightly open at idle, i'm talking it hardly shows up as 1% on the TPS gauge, 2% tops. Are stock TB's open at idle at all or are they totally shut? Should I have my itbs totally shut and just configure the map to give more air?

EDIT: weirdest thing is that when i pop the throttle the map goes to the appropriate level, and when i let off the MAP drops to 30, then pops back up to 60-65 for idling

Last edited by N3v; Jul 29, 2008 at 03:22 PM.
Old Jul 29, 2008 | 03:44 PM
  #2  
Braineack's Avatar
Boost Czar
iTrader: (62)
 
Joined: May 2005
Posts: 80,552
Total Cats: 4,368
From: Chantilly, VA
Default

you should be idling smooth at 1000rpm and 42-45kPa. Does MS know what map sensor you are using?
Old Jul 29, 2008 | 04:44 PM
  #3  
N3v's Avatar
N3v
Thread Starter
Junior Member
 
Joined: May 2008
Posts: 314
Total Cats: 1
From: Nashville/Knoxville, TN
Default

was using base map from diyautotune.com which had a 400kpa map and barometric correction turned on. i had the map set to 250kpa but barometric correction was turned on. isnt barometric correction only on those fancy 4 bar maps? I turned it off and now it's doing around 50 and i no longer see black smoke puffing out of my exhaust.
Old Jul 29, 2008 | 05:06 PM
  #4  
Braineack's Avatar
Boost Czar
iTrader: (62)
 
Joined: May 2005
Posts: 80,552
Total Cats: 4,368
From: Chantilly, VA
Default

well you can use two 250kPa sensors but ensure you have the correct stuff set...in your case it seems like the configurator needs to see 250map and MS needs to have baro off.

using the same base map, the fuji racing kit i helped tune was idling perfectly smooth at 950-1000RPM at 45kPa.
Old Jul 30, 2008 | 02:53 AM
  #5  
N3v's Avatar
N3v
Thread Starter
Junior Member
 
Joined: May 2008
Posts: 314
Total Cats: 1
From: Nashville/Knoxville, TN
Default

well it's right at around 50, but running really smooth. is there any chance you might have access to a fuel map for itbs?
Old Jul 30, 2008 | 02:56 AM
  #6  
KPLAFIN's Avatar
Elite Member
iTrader: (1)
 
Joined: Jun 2007
Posts: 2,945
Total Cats: 3
From: VA, Germany, Afghanistan
Default

Somebody likes zip ties.
Old Jul 30, 2008 | 08:56 AM
  #7  
Braineack's Avatar
Boost Czar
iTrader: (62)
 
Joined: May 2005
Posts: 80,552
Total Cats: 4,368
From: Chantilly, VA
Default

Originally Posted by N3v
well it's right at around 50, but running really smooth. is there any chance you might have access to a fuel map for itbs?

this was semi-tuned, then i rescaled it. but should be a good start


Old Jul 30, 2008 | 10:52 AM
  #8  
N3v's Avatar
N3v
Thread Starter
Junior Member
 
Joined: May 2008
Posts: 314
Total Cats: 1
From: Nashville/Knoxville, TN
Default

braineack, you are my hero.

And yes, I do like zip ties. they hold my life together.

but anyway, braineack can you tell me a little more about this tune? why did you rescale it? is this tune a little rich?

Last edited by N3v; Jul 30, 2008 at 03:31 PM.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Full_Tilt_Boogie
Build Threads
84
Apr 12, 2021 04:21 PM
Zaphod
MEGAsquirt
47
Oct 26, 2018 11:00 PM
StratoBlue1109
Miata parts for sale/trade
21
Sep 30, 2018 01:09 PM
stoves
Suspension, Brakes, Drivetrain
5
Apr 21, 2016 03:00 PM
The Gleas
MEGAsquirt
3
Oct 1, 2015 09:30 AM


Thread Tools
Search this Thread

All times are GMT -4. The time now is 10:47 AM.