IAT/CLT issues with MS
#1
Miotta FTW!
Thread Starter
iTrader: (24)
Join Date: Jun 2006
Location: Chicagoland, IL
Posts: 4,290
Total Cats: 31
IAT/CLT issues with MS
So my car is running! Thanks to all that have helped with my MS issues so far.
I still have 2 issues though. I get incorrect IAT and CLT readings
Mazda CLT
GM IAT
easythermed... if i did it properly... for mazda clt in C, and gm iat in F. With numbers per the rx7 and gm defaults.
I'm getting - IAT numbers and what I feel is high CLT... (crusing around temp is 83c)
I have a 2.490 resistor in r4 (clt) and a 2.2 resistor in r7.
Help me... i have car out now! So i can work on it quickly instead of 1.5hr drive.
I still have 2 issues though. I get incorrect IAT and CLT readings
Mazda CLT
GM IAT
easythermed... if i did it properly... for mazda clt in C, and gm iat in F. With numbers per the rx7 and gm defaults.
I'm getting - IAT numbers and what I feel is high CLT... (crusing around temp is 83c)
I have a 2.490 resistor in r4 (clt) and a 2.2 resistor in r7.
Help me... i have car out now! So i can work on it quickly instead of 1.5hr drive.
#3
Miotta FTW!
Thread Starter
iTrader: (24)
Join Date: Jun 2006
Location: Chicagoland, IL
Posts: 4,290
Total Cats: 31
No boosting yet, its just driving around. Once thermostat opens it just runs at same temp. No movement really unless i stop. So the CLT is close then... thats good to know.
Any thoughts on IAT? Its GM... with one wire to sensor input and other to ecu ground. It is setup with GM defaults, F, and 2200 in the ohm box. It reads - though...
Any thoughts on IAT? Its GM... with one wire to sensor input and other to ecu ground. It is setup with GM defaults, F, and 2200 in the ohm box. It reads - though...
#5
Miotta FTW!
Thread Starter
iTrader: (24)
Join Date: Jun 2006
Location: Chicagoland, IL
Posts: 4,290
Total Cats: 31
I get -13c when crusing for my IAT reading. I think it was -1c at startup today.
Looks like CLT is accurate though, thats one down.
BTW... running fine on the DIY autotune stuff. I had to configure my map with their setup and also switch my two ignition wires on my harness. All good now though.
Looks like CLT is accurate though, thats one down.
BTW... running fine on the DIY autotune stuff. I had to configure my map with their setup and also switch my two ignition wires on my harness. All good now though.
#7
Miotta FTW!
Thread Starter
iTrader: (24)
Join Date: Jun 2006
Location: Chicagoland, IL
Posts: 4,290
Total Cats: 31
I haven't heard fans kick on yet... so that is sorta good. I know it works with my wiring at least when jumpered at the diagnostic port.
Yah... pulled i get the bad reading. I already used a 2.2 instead of a 2.49 because i broke it when i pulled it last time... and realized that in standalone... i want it there
So yeah... real thoughts? Its only thing keeping me from truely tuning it...
Yah... pulled i get the bad reading. I already used a 2.2 instead of a 2.49 because i broke it when i pulled it last time... and realized that in standalone... i want it there
So yeah... real thoughts? Its only thing keeping me from truely tuning it...
#9
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Only if he wired it that way. My MS turns the cooling fan on at 175 (probably too low but adjustable in software).
Dave, verify voltage output from AIT with DMM. Then make sure the AIT wire is actually hooked to the MS.
Dave, verify voltage output from AIT with DMM. Then make sure the AIT wire is actually hooked to the MS.
#10
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
duh, keep forgetting you are stand alone....heck why am i not standalone yet? i just got wire up the fans and idle valve.
make sure when you use easytherm the bias resistor settings reflect which resistor you are using.
make sure when you use easytherm the bias resistor settings reflect which resistor you are using.
#11
Miotta FTW!
Thread Starter
iTrader: (24)
Join Date: Jun 2006
Location: Chicagoland, IL
Posts: 4,290
Total Cats: 31
I have my fans on the stock thermoswitch... no ecu needed.
I'll check my iat wiring and see if anything obvious shows up. It's got a 2.2ohm resistor in r7, which i put into easytherm. Hopefully I did it correctly.
I'll check my iat wiring and see if anything obvious shows up. It's got a 2.2ohm resistor in r7, which i put into easytherm. Hopefully I did it correctly.
Thread
Thread Starter
Forum
Replies
Last Post
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM