Just picked up a "new" MS1 V3, what needs changing?
10-15-2010, 04:47 PM
#1
Newb
Thread Starter
Join Date: Mar 2010
Location: London, England
Posts: 17
Total Cats: 0
Just picked up a "new" MS1 V3, what needs changing?
Hi, I have just managed to get hold of a cheap MS1 V3 nd need to know what needs changing/modding and if anyone knows how it is currently setup.
[IMG] Uploaded with ImageShack.us[/IMG]
Sorry about the fuzzy pic, I have not seen a MS board with this much stuff on it and I assume much of it needs to go.
Sorry again for the nooby post but I would really appreciate some help, thanks guys
[IMG] Uploaded with ImageShack.us[/IMG]
Sorry about the fuzzy pic, I have not seen a MS board with this much stuff on it and I assume much of it needs to go.
Sorry again for the nooby post but I would really appreciate some help, thanks guys
Reply
0
0
10-15-2010, 04:52 PM
#2
My suggestion to you would be to take a look at Brain's diagrams in the Megasquirt section of the forum here.
There is a "what you need to install" diagram. Also read up on the miata input and spark mods. They will need to be installed on the board before it will run your car.
If it helps, get a copy of the megamanual and read through it to check that everything was installed properly.
There is a "what you need to install" diagram. Also read up on the miata input and spark mods. They will need to be installed on the board before it will run your car.
If it helps, get a copy of the megamanual and read through it to check that everything was installed properly.
Reply
0
0
10-15-2010, 05:49 PM
#5
Newb
Thread Starter
Join Date: Mar 2010
Location: London, England
Posts: 17
Total Cats: 0
From eBay, I'm assuming this is going to be difficult to reverse? Not too much of a problem as I got it for £100. Is the fact it has been built to trigger off vr only going to be a problem?
Reply
0
0
10-15-2010, 06:21 PM
#7
Newb
Thread Starter
Join Date: Mar 2010
Location: London, England
Posts: 17
Total Cats: 0
Good times, Would anyone be able to share some useful links? I appologise if they are obvious but it's 11.30pm here and I'm shattered/7 stella's down... thanks for your help so far though
Reply
0
0
10-15-2010, 06:43 PM
#9
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
There are those that would argue that the hall components are optional and ignored when properly set up. Seriously, I just set up a MS2 V3.57 for a Miata triggering off VR INV with 12 volt pullup, and a 5V pullup on the 2nd input. It's working great. The "hall" input was originally intended for coil input for fuel only applications, and the "VR" input was intended for hall or VR signals. Point being that there's more than one way to do it...
Reply
0
0
10-16-2010, 04:46 AM
#10
Newb
Thread Starter
Join Date: Mar 2010
Location: London, England
Posts: 17
Total Cats: 0
Morning, right, one last noob question before I break out the soldering iron...
Can all the existing components be left in place when I do the mx5 based mods? (I'm assuming probably not, but hoping yes lol)
Can all the existing components be left in place when I do the mx5 based mods? (I'm assuming probably not, but hoping yes lol)
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
elesjuan
Build Threads
9
11-14-2018 12:18 PM
aznDragonX
Miata parts for sale/trade
5
07-29-2009 01:42 PM
