MSPNP 2 start help
#1
MSPNP 2 start help
Hi there,
I'm having an issue starting my car after having switched to my megasquirt and I'm hoping an extra set of eyes can catch a mistake I may have made. It turns and turns but I don't even get a sputter. I attached my tune and a datalog of the start.
I used MS2-Extra Conversion Manual and http://www.msextra.com/doc/ms2extra/...n_Ignition.htm as my points of reference for navigating through Tunderstudio.
Car is a 2000, have MSPNP 2, Deatschwerks 700cc injectors, Aem Uego and BEGI S1 kit.
Thanks
I'm having an issue starting my car after having switched to my megasquirt and I'm hoping an extra set of eyes can catch a mistake I may have made. It turns and turns but I don't even get a sputter. I attached my tune and a datalog of the start.
I used MS2-Extra Conversion Manual and http://www.msextra.com/doc/ms2extra/...n_Ignition.htm as my points of reference for navigating through Tunderstudio.
Car is a 2000, have MSPNP 2, Deatschwerks 700cc injectors, Aem Uego and BEGI S1 kit.
Thanks
#2
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Did you not use the included CD to load TunerStudio with the pre-made project? Your tune file suggests you created your own project.
Go to File > Project > Project Properties (or control + p)
Click on settings tab
Ensure that MegaSquirt/Microsquirt selection is set to Microsquirt Module/MSPNP.
Go to File > Project > Project Properties (or control + p)
Click on settings tab
Ensure that MegaSquirt/Microsquirt selection is set to Microsquirt Module/MSPNP.
#4
Ben- You're correct. In an effort to not make any mistakes I believe I over-thought the situation and confused myself and created my own. I flashed back to the map provided for 99-00 with the only change I made to the reqfuel but that didn't work either.
The selection is the microsquirt/MSPNP. Does that make sense, it was purchased from 949Racing...the other selection is the MS 2 v3 that it could possibly be. Megasquirt PnP Miata 99-00
Matt- I believe I created my own map that I'm sure was hideously incorrect. But I did scale the injectors as 1845..4..700..14.7 and came out with 4.4. After going back to the map provided and scaling the injectors it still wouldn't start.
I didn't work with the timing because the instructions say to do that once the car is started.
The selection is the microsquirt/MSPNP. Does that make sense, it was purchased from 949Racing...the other selection is the MS 2 v3 that it could possibly be. Megasquirt PnP Miata 99-00
Matt- I believe I created my own map that I'm sure was hideously incorrect. But I did scale the injectors as 1845..4..700..14.7 and came out with 4.4. After going back to the map provided and scaling the injectors it still wouldn't start.
I didn't work with the timing because the instructions say to do that once the car is started.
Last edited by rtr2885; 10-28-2013 at 06:21 PM. Reason: failure
#5
Back at this again. After attempting to load the tune provided I get this:
9 Warnings:
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:flexport equal to the proposed "JS11"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:spk_config_spka equal to the proposed "JS10"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:rtbaroport equal to the proposed "MS2 AD6/JS5"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:ego2port equal to the proposed "MS2 AD6/JS5"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:boost_ctl_pins equal to the proposed "JS11"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:tacho_opt3f equal to the proposed "D14"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:launch_opt_pins equal to the proposed "PE0/JS7"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins2 equal to the proposed "IAC1+2"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins equal to the proposed "PE0/JS7"
What am I missing here? Is there anyway to start fresh?
9 Warnings:
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:flexport equal to the proposed "JS11"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:spk_config_spka equal to the proposed "JS10"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:rtbaroport equal to the proposed "MS2 AD6/JS5"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:ego2port equal to the proposed "MS2 AD6/JS5"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:boost_ctl_pins equal to the proposed "JS11"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:tacho_opt3f equal to the proposed "D14"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:launch_opt_pins equal to the proposed "PE0/JS7"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins2 equal to the proposed "IAC1+2"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins equal to the proposed "PE0/JS7"
What am I missing here? Is there anyway to start fresh?
Thread
Thread Starter
Forum
Replies
Last Post