updated firmware on MSPNP 2 now runs like crap - Miata Turbo Forum - Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


MEGAsquirt A place to collectively sort out this megasquirt gizmo

Reply
 
 
 
LinkBack Thread Tools
Old 06-16-2015, 09:10 PM   #1
Newb
Thread Starter
 
Join Date: Aug 2012
Posts: 35
Total Cats: -4
Default updated firmware on MSPNP 2 now runs like crap

Ok guys, upgraded my MSPNP 2 to Version 3.3 and now it runs like total ****. was running great battery died. had to change the battery. Then AC idle up wouldn't work any more on the variable resister on the board. Talked to Phil and he stated possible corruption with the firmware. SOOOO long story short updated firmware. checked settings in tunerstudio, reconnected the ignitor, fired it up and bam runs like ****. AFR will not change no matter what I do. I'm sure its something I'm missing. but I can't figure out what it could be.
Attached Files
File Type: msq afterfirmware_michaeldaily_91Miata.msq (110.4 KB, 75 views)
File Type: msl 2015-06-16_18.36.17.msl (624.9 KB, 75 views)
saverok is offline   Reply With Quote
Old 06-17-2015, 10:21 AM   #2
Supporting Vendor
 
Matt Cramer's Avatar
 
Join Date: Sep 2006
Posts: 2,266
Total Cats: 51
Default

First thing to check: Are the CLT, MAT, and MAP readings correct?
Matt Cramer is offline   Reply With Quote
Old 06-17-2015, 11:01 AM   #3
Newb
Thread Starter
 
Join Date: Aug 2012
Posts: 35
Total Cats: -4
Default

Quote:
Originally Posted by Matt Cramer View Post
First thing to check: Are the CLT, MAT, and MAP readings correct?
looks to be. Vac reading seems to be different than the gauge.

my main concern is that the O2 AFR reading doesn't deviate at all. Should I have also unplugged my O2 before updating firmware? is it possible it got burned up? something I'm missing that needs to be reset up?
saverok is offline   Reply With Quote
Old 06-17-2015, 11:18 AM   #4
Ben
Supporting Vendor
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

Did it work before?

Did you got to tools > calibrate AFR table and set up your wideband?
Ben is offline   Reply With Quote
Old 06-17-2015, 11:21 AM   #5
Newb
Thread Starter
 
Join Date: Aug 2012
Posts: 35
Total Cats: -4
Default

Yes sir worked before. Was running smooth minus the AC idle up. Before the battery died it has been running smooth.

Phil sent me a message told me to start a new project with the new firmware and load in the msq. I'll try that this after noon and see if that helps or solves it.
saverok is offline   Reply With Quote
Old 06-17-2015, 11:41 AM   #6
Boost Czar
iTrader: (61)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 72,899
Total Cats: 1,792
Default

what firmware did you have before 3.3.3? a lot of settings need to be changed between newer and older firmwares.
Braineack is offline   Reply With Quote
Old 06-17-2015, 11:53 AM   #7
Newb
Thread Starter
 
Join Date: Aug 2012
Posts: 35
Total Cats: -4
Default

Quote:
Originally Posted by Braineack View Post
what firmware did you have before 3.3.3? a lot of settings need to be changed between newer and older firmwares.
it was the original firmware from 2012 when I got it. Version 2 something I think. I followed the readme's setting changes. I didnt start a new project. here's to hoping that part helps

BUT if you have some things I need to make sure to check settings wise or anything else please let me know. going to work on it some more this evening.
saverok is offline   Reply With Quote
Old 06-17-2015, 11:54 AM   #8
Boost Czar
iTrader: (61)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 72,899
Total Cats: 1,792
Default

yeah, you need to go through the map section by section to make sure all settings still make sense. i notice a lot of times idle code will get turned off completely, or switch to warmup only or something odd.
Braineack is offline   Reply With Quote
Old 06-17-2015, 11:57 AM   #9
Newb
Thread Starter
 
Join Date: Aug 2012
Posts: 35
Total Cats: -4
Default

Quote:
Originally Posted by Braineack View Post
yeah, you need to go through the map section by section to make sure all settings still make sense. i notice a lot of times idle code will get turned off completely, or switch to warmup only or something odd.
ok I'll start a new project and double check that section.

should I have unplugged my O2 as well when I did the firmware update? didn't see anything say that. I'm just hoping that it isn't fried and its just an issue with the codes. old project and all.
saverok is offline   Reply With Quote
Old 06-17-2015, 09:40 PM   #10
Newb
Thread Starter
 
Join Date: Aug 2012
Posts: 35
Total Cats: -4
Default



here is the tune settings with a new project as Phil asked for and the data log. you can see that my O2 is getting a reading finally But its still sounds like it isn't hitting right and running like ****.
Attached Files
File Type: msl 2015-06-17_18.55.27.msl (277.5 KB, 58 views)
File Type: msq AfterFirmware_NewProject_MDaily_Miata.msq (110.2 KB, 61 views)
saverok is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Project Gemini - Turbo Civic on the Cheap Full_Tilt_Boogie Build Threads 59 Yesterday 09:00 PM
Changing from 460cc to flow force 610cc in diypnp 90 Turbo MEGAsquirt 19 10-19-2015 04:23 PM
Time to start learning and play with tuning The Gleas MEGAsquirt 3 10-01-2015 10:30 AM
In need of base map for stock 1997 brandonbkd MEGAsquirt 0 09-29-2015 12:52 AM
why is my car running like pewp? (tune/datalog) itsMikey MSPNP 3 09-28-2015 07:40 AM


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 06:57 PM.