megasquirt first start-up guide?
#1
Senior Member
Thread Starter
iTrader: (9)
Join Date: Jun 2007
Location: NH
Posts: 1,013
Total Cats: 21
megasquirt first start-up guide?
This may have been covered, and if so, I apologize, but is there a thread or checklist of things to do with one of Braineack's megasquirts for the first start-up? I'm having trouble getting my car to fire, and want to make sure I'm not missing anything. I have no knowledge of the tuning software, as I'm completely new to all of this. So again, my apologies if this has been covered. Also, should I be using megatune or tunerstudio? I will be breaking in the motor and doing the tuning on the dyno, but am trying to verify I can start the car before I bring it in (for a little background info).
#4
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
shows how great my memory is!
what are the details of your setup? im assuming you havent touched any software settings. Let me know at the map I loaded if it's on my laptop here, it may be on my old one.
what are the details of your setup? im assuming you havent touched any software settings. Let me know at the map I loaded if it's on my laptop here, it may be on my old one.
#5
Senior Member
Thread Starter
iTrader: (9)
Join Date: Jun 2007
Location: NH
Posts: 1,013
Total Cats: 21
full standalone
750cc high imp injectors
removed afm
variable tps
COPs
built 1.8l
lots of headwork
258 cams
4bar map sensor
aem wideband o2
How do I find the map you loaded? I haven't touched any settings. Sorry about all the questions, I'm completely new to all this.
#10
Senior Member
Thread Starter
iTrader: (9)
Join Date: Jun 2007
Location: NH
Posts: 1,013
Total Cats: 21
I attached the file. I installed the IAT sensor (I can see on tuner studio that it's reading the ambient temp now) and I did run that vac line yes. When I try to start the car it just keeps cranking- no sputtering or anything.
#13
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
under basic settings > engine constants
change MAP type to 400kPa and barometric corrections to off.
see if that helps. can you verify that you're getting spark and/or fuel. do you see RPMs on the virtual dashboard when cranking?
change MAP type to 400kPa and barometric corrections to off.
see if that helps. can you verify that you're getting spark and/or fuel. do you see RPMs on the virtual dashboard when cranking?
#14
Senior Member
Thread Starter
iTrader: (9)
Join Date: Jun 2007
Location: NH
Posts: 1,013
Total Cats: 21
I know I'm getting fuel. I'm going to play with it some more tonight (check spark, do a comp. test). I haven't seen RPMs while I've been cranking, but I believe I was in "offline" mode. I will check that tonight as well.
#15
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
if for some reason the MS is not reading the CAS correctly and doesn't show RPMs on the virtual gauge, it will never spark. So please report back and let me know. make sure you're not flooded right now...
#20
Senior Member
Thread Starter
iTrader: (9)
Join Date: Jun 2007
Location: NH
Posts: 1,013
Total Cats: 21
ok new information.
I'm getting just over 100 psi on the compression test, all 4 cylinders are exactly the same.
I'm getting spark on cylinders 2 and 3.
Cylinders 1 and 4 are not getting a spark. I swapped all of the COPs to the "working spots" on the COP harness (2 & 3), and was able to get a spark. I'm going to try and swap over the stock igniter, coil, and get some plug wires and see if I can get it to start, or even stumble then.
I'm getting just over 100 psi on the compression test, all 4 cylinders are exactly the same.
I'm getting spark on cylinders 2 and 3.
Cylinders 1 and 4 are not getting a spark. I swapped all of the COPs to the "working spots" on the COP harness (2 & 3), and was able to get a spark. I'm going to try and swap over the stock igniter, coil, and get some plug wires and see if I can get it to start, or even stumble then.
Last edited by mighty mouse; 06-02-2010 at 09:20 PM.